Projects / SPI daisy chain of displays

SPI daisy chain of displays

Beginner1 hGuided buildReviewed

Build it step by step

0 of 6 done
  1. NANO8.9 mA

    Wire one module

    Connect the first module to the Nano and test it with the LedControl example.

  2. NANO

    Add the chain

    Link DOUT to DIN for each next module and share CLK and CS.

  3. NANO

    Check the order

    Light device 0 only and see which module it is.

  4. NANO

    Show different data

    Run the sketch and see counting, text, a heart and an arrow.

  5. NANO

    Look at the bus

    If you have a logic analyser, see four 16-bit words per update on DIN.

  6. NANO

    Change the order

    Swap device numbers if the displays appear reversed.

In short

How do you build an SPI daisy chain of displays?

Chain four MAX7219 displays on one SPI bus and send different text to each. You need Arduino Nano, 8-digit 7-segment module (MAX7219) × 2, MAX7219 8x8 LED matrix module × 2 and 5 V 2 A USB adapter. It takes 6 steps and about 60 minutes.

Level
Beginner
Time
About 60 min
Parts
4

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Nano D11First module DINData
Nano D13First module CLK, and all other CLK pinsClock to every module
Nano D10First module CS, and all other CS pinsLoad to every module
First module DOUTSecond module DINChain
Second module DOUTThird module DINChain
Third module DOUTFourth module DINChain
5 V adapter + and -VCC and GND of every module and Nano GNDShared power

Code

Arduino IDE, board "Arduino Nano" (processor ATmega328P, or ATmega328P (Old Bootloader) for clones). Install "LedControl" by Eberhard Fahle. All four modules share CLK and CS and pass data on through DOUT to the next DIN. Each update shifts out one 16-bit command per module before CS is raised, and the library does this for you. The modules draw about 0.3 A each at full brightness, so run them from the 5 V adapter at low intensity and keep the Nano's ground joined to the adapter's ground. Use the matrix modules with a common arrangement (check the DIN side).

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

#include <LedControl.h>

LedControl lc = LedControl(11, 13, 10, 4);          // DIN, CLK, CS, number of devices
// Device 0 is the one wired to the Nano. If the order looks reversed, swap the device numbers below.
const byte HEART[8] = { 0x00, 0x66, 0xFF, 0xFF, 0xFF, 0x7E, 0x3C, 0x18 };
const byte ARROW[8] = { 0x08, 0x0C, 0xFE, 0xFF, 0xFE, 0x0C, 0x08, 0x00 };

void setup() {
  for (byte d = 0; d < 4; d++) {
    lc.shutdown(d, false);
    lc.setIntensity(d, 3);                          // low brightness keeps current down
    lc.clearDisplay(d);
  }
  for (byte r = 0; r < 8; r++) { lc.setRow(2, r, HEART[r]); lc.setRow(3, r, ARROW[r]); }   // the two matrices
}

void loop() {
  static unsigned long n = 0;
  unsigned long v = n++;
  for (byte i = 0; i < 8; i++) { lc.setDigit(0, i, v % 10, false); v /= 10; }   // first display counts up
  for (byte i = 0; i < 8; i++) lc.setChar(1, i, "HELP-  -"[7 - i], false);       // second display shows text
  delay(100);
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Power onCounter on the first display, text on the second
MatricesHeart and arrow shown
BrightnessEven and not too bright
Unplug the last moduleThe others still work

If it does not work

Only the first module works

Check DOUT to DIN links on the later ones.

Displays reversed

Swap the device numbers in the code.

Dim or flickers

Use the 5 V adapter, not the Nano pin.

Garbled characters

Check that CLK and CS go to every module.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the SPI daisy chain of displays?

Arduino Nano, 8-digit 7-segment module (MAX7219) × 2, MAX7219 8x8 LED matrix module × 2 and 5 V 2 A USB adapter.

How long does the SPI daisy chain of displays take to build?

About 60 minutes for a beginner maker, in 6 steps.

How do I know the SPI daisy chain of displays works?

Power on: Counter on the first display, text on the second. Matrices: Heart and arrow shown. Brightness: Even and not too bright.

Only the first module works: what should I check?

Check DOUT to DIN links on the later ones.

Displays reversed: what should I check?

Swap the device numbers in the code.

Dim or flickers: what should I check?

Use the 5 V adapter, not the Nano pin.

Garbled characters: what should I check?

Check that CLK and CS go to every module.