Projects / Serial plotter sensor lab

Serial plotter sensor lab

Beginner30 minGuided buildReviewed

Build it step by step

0 of 6 done
  1. UNOTMP3628.4°C

    Build the three sensors

    LDR divider on A0, pot on A1, TMP36 on A2.

  2. UNO

    Upload and open the plotter

    Choose Tools, Serial Plotter and set 115200 baud.

  3. UNO

    Watch the three traces

    Each appears in its own colour with its name.

  4. UNOTMP3628.4°C

    Play

    Turn the knob, cover the LDR with a hand and warm the TMP36 between your fingers.

  5. UNOTMP3628.4°C

    Compare ranges

    Light and knob run from 0 to 100, temperature from about 25 to 35.

  6. UNO

    Scale for clarity

    Try dividing or offsetting values so they fit the same range.

In short

How do you build a serial plotter sensor lab?

Plot an LDR, a pot and a temperature sensor live on the Arduino serial plotter. You need Arduino Uno R3, LDR Photoresistor, Potentiometer 10 kΩ, TMP36 temperature sensor, Resistor 10 kΩ, Breadboard 830 Tie Points, Jumper wires male to male (40 pcs, 20 cm) and USB A to micro-USB cable (data). It takes 6 steps and about 30 minutes.

Level
Beginner
Time
About 30 min
Parts
8

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
LDRUno 5V and A0, with 10 kΩ from A0 to GNDLight divider, brighter reads higher
Pot outer pinsUno 5V and GNDReference
Pot middle pinUno A1Knob
TMP36 pin 1 (left, flat side to you)Uno 5VSupply
TMP36 pin 2 (middle)Uno A2Output
TMP36 pin 3 (right)Uno GNDGround

Code

Arduino IDE, board "Arduino Uno". No libraries. Open Tools, then Serial Plotter, and set the baud to 115200. Scaling Light and Knob to 0 to 100 puts them on the same range as the temperature in degrees.

Runs on a virtual Arduino Uno in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

void setup() {
  Serial.begin(115200);
}

void loop() {
  int ldr = analogRead(A0);
  int pot = analogRead(A1);
  float mv = analogRead(A2) * 5000.0 / 1023.0;
  float tempC = (mv - 500.0) / 10.0;                 // TMP36: 500 mV at 0 C, 10 mV per degree

  // The plotter reads name:value pairs separated by commas, one line per sample
  Serial.print("Light:");  Serial.print(ldr * 100.0 / 1023.0); Serial.print(',');   // scaled to 0 to 100
  Serial.print("Knob:");   Serial.print(pot * 100.0 / 1023.0); Serial.print(',');
  Serial.print("TempC:");  Serial.println(tempC);
  delay(50);
}

What the serial monitor should show

Open the serial monitor at the baud rate in the code. This is what our simulator prints for a virtual Arduino Uno with its sensors at their default values. Your numbers will follow your real readings, but the format should match.

Light:50.05,Knob:50.15,TempC:200.24
Light:50.05,Knob:50.05,TempC:200.24
Light:50.05,Knob:49.95,TempC:199.76
Light:50.05,Knob:49.95,TempC:200.24
Light:49.95,Knob:49.95,TempC:200.24
Light:50.05,Knob:49.95,TempC:200.24

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Turn the potKnob trace rises and falls with the position
Cover the LDRLight trace drops
Hold the TMP36Temperature climbs by a few degrees
Room temperatureAbout 22 to 30 °C

If it does not work

Temperature reads strange

TMP36 is wired backwards. Check which side the flat face is on.

Plotter shows one line

The output is not in name:value format or the line ends are missing.

Noisy traces

Add 100 nF across the sensor supply and keep wires short.

Nothing shown

Wrong baud rate on the plotter.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the serial plotter sensor lab?

Arduino Uno R3, LDR Photoresistor, Potentiometer 10 kΩ, TMP36 temperature sensor, Resistor 10 kΩ, Breadboard 830 Tie Points, Jumper wires male to male (40 pcs, 20 cm) and USB A to micro-USB cable (data).

How long does the serial plotter sensor lab take to build?

About 30 minutes for a beginner maker, in 6 steps.

How do I know the serial plotter sensor lab works?

Turn the pot: Knob trace rises and falls with the position. Cover the LDR: Light trace drops. Hold the TMP36: Temperature climbs by a few degrees.

Temperature reads strange: what should I check?

TMP36 is wired backwards. Check which side the flat face is on.

Plotter shows one line: what should I check?

The output is not in name:value format or the line ends are missing.

Noisy traces: what should I check?

Add 100 nF across the sensor supply and keep wires short.

Nothing shown: what should I check?

Wrong baud rate on the plotter.