Projects / Electronic tamper-evident seal

Electronic tamper-evident seal

Intermediate2.5 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. Program the chip

    Use Arduino as ISP.

  2. 14.4 mA

    Test the loop

    Hold the pin low and watch the LED stay off.

  3. 14.5 mA

    Break the loop

    The LED starts blinking.

  4. ENAMEL14.5 mA

    Wire the seal

    Fine wire through the lid seam.

  5. Read the EEPROM

    Dump it with the programmer.

  6. Measure the sleep current

    A few microamps.

  7. Test the lid

    Open it a few times in a dry run.

In short

How do you build an electronic tamper-evident seal?

A seal for a box logs when it was opened, by breaking a fine wire loop. You need ATtiny85-20PU microcontroller, Enamelled copper wire (magnet wire, 0.3 mm), CR2032 coin cell, CR2032 coin cell holder, LED 5 mm red and Resistor 220 Ω. It takes 7 steps and about 150 minutes.

Level
Intermediate
Time
About 150 min
Parts
6

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Coin cell plusATtiny85 pin 8Power
Coin cell minusATtiny85 pin 4Ground
Fine wire loopATtiny85 PB1 (pin 6) to ground, with the internal pull-upLoop intact reads low
Red LEDATtiny85 PB0 (pin 5) through 220 Ω to groundOpened indicator

Code

A hair-thin enamelled wire runs through the lid seam in a loop; when someone opens the box the loop snaps, the input goes high through the pull-up, and the chip stores how long it had been armed, counted in 8-second watchdog ticks, then blinks a red LED every 8 seconds from then on. Strip the enamel only at the two ends you connect. Read the stored count by dumping the EEPROM through the programmer: byte 0 is the opened flag and bytes 1 to 4 hold the ticks since arming. Sleep current is a few microamps, so a CR2032 lasts a long time. This is a tamper-evident seal for your own boxes, such as sample or equipment cases, not a lock: a patient person can repair a broken wire, and it does not stop anyone, it only tells you something happened. Coin cells are dangerous to swallow, so keep the seal and spare cells away from young children.

Runs on a virtual ATtiny85 in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// Tamper seal: counts 8-second ticks, saves the count when the wire loop breaks. Board: ATtiny85 (ATTinyCore, 1 MHz).
#include <avr/sleep.h>
#include <avr/wdt.h>
#include <avr/interrupt.h>
#include <EEPROM.h>
const int LOOP_PIN = 1, LED = 0;
volatile unsigned long ticks = 0;                     // 8 seconds per tick, about 100 years of range
ISR(WDT_vect) { ticks++; }
ISR(PCINT0_vect) {}
void watchdog8s() {
  MCUSR &= ~_BV(WDRF);
  WDTCR |= _BV(WDCE) | _BV(WDE);
  WDTCR = _BV(WDIE) | _BV(WDP3) | _BV(WDP0);          // interrupt only, 8 s period
}
void sleepNow() {
  set_sleep_mode(SLEEP_MODE_PWR_DOWN);
  sleep_enable(); sei(); sleep_cpu(); sleep_disable();
}
void setup() {
  pinMode(LOOP_PIN, INPUT_PULLUP); pinMode(LED, OUTPUT);
  GIMSK |= _BV(PCIE); PCMSK |= _BV(PCINT1);
  watchdog8s();
  if (EEPROM.read(0) != 0xA5 && digitalRead(LOOP_PIN) == LOW) ticks = 0;   // armed: loop intact
}
void loop() {
  if (EEPROM.read(0) == 0xA5) {                       // already opened: blink every 8 seconds
    digitalWrite(LED, HIGH); delay(30); digitalWrite(LED, LOW);
    sleepNow();
    return;
  }
  if (digitalRead(LOOP_PIN) == HIGH) {                // loop broken
    unsigned long t = ticks;
    EEPROM.put(1, t);                                 // ticks since arming, 8 s each
    EEPROM.write(0, 0xA5);
    return;
  }
  sleepNow();                                         // wake on the watchdog tick or the pin change
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Loop intactLED stays off
Loop brokenLED blinks every 8 seconds
EEPROMOpened flag and tick count saved
BatteryMonths or years of life

If it does not work

Opens by itself

Check the wire joint and its pull-up.

No blink

Check LED polarity and the 220 Ω resistor.

Count wrong

Use the correct fuse and clock settings.

Chip never sleeps

Check the watchdog setup.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the electronic tamper-evident seal?

ATtiny85-20PU microcontroller, Enamelled copper wire (magnet wire, 0.3 mm), CR2032 coin cell, CR2032 coin cell holder, LED 5 mm red and Resistor 220 Ω.

How long does the electronic tamper-evident seal take to build?

About 150 minutes for a intermediate maker, in 7 steps.

How do I know the electronic tamper-evident seal works?

Loop intact: LED stays off. Loop broken: LED blinks every 8 seconds. EEPROM: Opened flag and tick count saved.

Opens by itself: what should I check?

Check the wire joint and its pull-up.

No blink: what should I check?

Check LED polarity and the 220 Ω resistor.

Count wrong: what should I check?

Use the correct fuse and clock settings.

Chip never sleeps: what should I check?

Check the watchdog setup.