Build it step by step
0 of 7 doneBuild the clock
555 astable as in the table. Confirm it blinks a test LED.
Add the buffer
Pass the 555 output through two inverters from the 74HC04.
Wire the register
Clock to pins 11 and 12, OE to GND, SRCLR to the power-on reset.
Feed back
QH' (pin 9) to the inverter, the inverter to SER (pin 14).
Add the LEDs
Each output through 330 Ω to ground.
Power up
The row fills one LED at a time, then empties one at a time.
Count the states
There are 16 states in the full cycle.
How do you build a johnson counter light chaser?
A shift register with inverted feedback makes a Johnson counter that fills and empties a row of LEDs. You need 74HC595 Shift Register, 74HC04 hex inverter, NE555 Timer IC, Resistor 10 kΩ × 3, Electrolytic capacitor 10 µF × 2, LED 5 mm red × 8, Resistor 330 Ω × 8, Breadboard 830 Tie Points, Jumper wires male to male (40 pcs, 20 cm), Breadboard power supply module (MB102) and 12 V 2 A DC adapter. It takes 7 steps and about 60 minutes.
- Level
- Beginner
- Time
- About 60 min
- Parts
- 11
Parts list
- Integrated CircuitsBuy
- Integrated CircuitsBuy
- Integrated CircuitsBuyNE555 Timer IC × 1
- PassivesBuyResistor 10 kΩ × 3
- PassivesBuy
- SemiconductorsBuyLED 5 mm red × 8
- PassivesBuyResistor 330 Ω × 8
- PrototypingBuy
- PrototypingBuy
- PowerBuy
- PowerBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| 555 astable | 10 kΩ from +5 V to pin 7, 10 kΩ from pin 7 to pins 2 and 6, 10 µF to GND, pins 4 and 8 to +5 V | About 4.8 Hz clock |
| 555 pin 3 | 74HC04 pin 3, pin 4 to pin 5, pin 6 is the clean clock | Two inverters buffer the weak 555 output |
| 74HC04 pin 6 | 74HC595 pin 11 (SRCLK) and pin 12 (RCLK) | Shift and latch on the same edge |
| 74HC595 pin 9 (QH') | 74HC04 pin 1; pin 2 | 74HC595 pin 14 (SER) |
| 74HC595 pin 13 (OE) | GND | Outputs enabled |
| 74HC595 pin 10 (SRCLR) | 10 kΩ to +5 V and 10 µF to GND | Clears at power up |
| 74HC595 QA to QH (pins 15, 1 to 7) | 330 Ω then LED to GND | Eight LEDs |
| Power | 74HC595 pin 16 and 74HC04 pin 14 to +5 V, grounds to GND | Common supply |
| Unused 74HC04 inputs (9, 11, 13) | GND | Tie off |
No code needed
No code. Power: a breadboard power supply module (MB102) from the 12 V adapter, with its jumper set to 5 V. The inverted feedback means a 1 is shifted in until all eight outputs are 1, then a 0 until all are 0, giving 16 states. The two 74HC04 gates in series reshape the 555's output, whose high level is a little low for 74HC inputs.
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| After reset | Starts with all LEDs off |
| Every clock | One more LED turns on until all eight are lit |
| Then | They turn off one at a time in the same order |
| Cycle length | 16 clock pulses |
If it does not work
Odd pattern after power up
The register started in an invalid state. Power cycle or add a reset button.
Nothing happens
Check the clock. The 555 may not reach the 595.
LEDs only half work
A 330 Ω resistor or LED is backwards.
Pattern is one step late
SRCLK and RCLK share an edge, so the output lags by one clock. That is normal.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the johnson counter light chaser?
74HC595 Shift Register, 74HC04 hex inverter, NE555 Timer IC, Resistor 10 kΩ × 3, Electrolytic capacitor 10 µF × 2, LED 5 mm red × 8, Resistor 330 Ω × 8, Breadboard 830 Tie Points, Jumper wires male to male (40 pcs, 20 cm), Breadboard power supply module (MB102) and 12 V 2 A DC adapter.
How long does the johnson counter light chaser take to build?
About 60 minutes for a beginner maker, in 7 steps.
How do I know the johnson counter light chaser works?
After reset: Starts with all LEDs off. Every clock: One more LED turns on until all eight are lit. Then: They turn off one at a time in the same order.
Odd pattern after power up: what should I check?
The register started in an invalid state. Power cycle or add a reset button.
Nothing happens: what should I check?
Check the clock. The 555 may not reach the 595.
LEDs only half work: what should I check?
A 330 Ω resistor or LED is backwards.
Pattern is one step late: what should I check?
SRCLK and RCLK share an edge, so the output lags by one clock. That is normal.
