Projects / RGB colour mixer

RGB colour mixer

Beginner35 minGuided buildReviewed
Arduino UnoA0A1A2D9D10D11GNDRedGreenBlueR255 G128 B0Serial
Serial at 9600 baud

Tap a part to see what it does.

Tap the parts to see what each one does. A teaching simulation, not a circuit simulator.

Build it step by step

0 of 4 done
  1. UNO19.4 mA

    Place the RGB LED

    Longest leg to the ground rail.

  2. UNO

    Three resistors

    Each colour leg through 220 Ω to D9, D10, D11.

  3. UNO

    Three knobs

    Ends to 5V and GND, wipers to A0, A1, A2.

  4. UNO

    Upload and mix

    Turn the knobs and paste the hex code into any colour picker.

In short

How do you build an RGB colour mixer?

Three knobs set the red, green and blue brightness of one RGB LED, and the serial monitor prints the colour as a web hex code. You need Arduino Uno R3, RGB LED 5 mm common cathode, Potentiometer 10 kΩ × 3, Resistor 220 Ω × 3 and Breadboard 830 Tie Points. It takes 4 steps and about 35 minutes.

Level
Beginner
Time
About 35 min
Parts
5

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Pot wipersA0 / A1 / A2Red / green / blue knobs (ends to 5V and GND)
D9 → 220 ΩRGB red legPWM red
D10 → 220 ΩRGB green legPWM green
D11 → 220 ΩRGB blue legPWM blue
RGB longest legGNDCommon cathode

Code

No libraries. analogRead gives 0 to 1023; dividing by 4 gives the 0 to 255 range of analogWrite. For a common-anode LED, use 255 − value.

Runs on a virtual Arduino Uno in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

void setup() { Serial.begin(9600); }

void loop() {
  int r = analogRead(A0) / 4, g = analogRead(A1) / 4, b = analogRead(A2) / 4;
  analogWrite(9, r); analogWrite(10, g); analogWrite(11, b);
  char hex[8];
  sprintf(hex, "#%02X%02X%02X", r, g, b);
  Serial.println(hex);
  delay(200);
}

What the serial monitor should show

Open the serial monitor at the baud rate in the code. This is what our simulator prints for a virtual Arduino Uno with its sensors at their default values. Your numbers will follow your real readings, but the format should match.

#808080
#807F7F
#807F80
#7F7F80
#807F80
#808080

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Red and green full, blue offYellow light, #FFFF00
All fullClose to white (often slightly blue or pink)
All zeroLED off, #000000

If it does not work

Colours inverted

Common-anode LED: long leg to 5V and invert the values.

One colour never lights

Wrong leg order: check the pinout with a meter on diode mode.

Flicker

Normal at very low values; keep values above about 5.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the RGB colour mixer?

Arduino Uno R3, RGB LED 5 mm common cathode, Potentiometer 10 kΩ × 3, Resistor 220 Ω × 3 and Breadboard 830 Tie Points.

How long does the RGB colour mixer take to build?

About 35 minutes for a beginner maker, in 4 steps.

How do I know the RGB colour mixer works?

Red and green full, blue off: Yellow light, #FFFF00. All full: Close to white (often slightly blue or pink). All zero: LED off, #000000.

Colours inverted: what should I check?

Common-anode LED: long leg to 5V and invert the values.

One colour never lights: what should I check?

Wrong leg order: check the pinout with a meter on diode mode.

Flicker: what should I check?

Normal at very low values; keep values above about 5.