Projects / Resistor value reader

Resistor value reader

Intermediate1.5 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. NANOCROCOD

    Build the divider

    One reference and a clip lead.

  2. NANO

    Read a known resistor

    Compare with the meter.

  3. NANO

    Add the second and third ranges

    Switch pins to inputs.

  4. NANO

    Choose the best range

    Reading in the middle.

  5. NANO

    Snap to E24

    Nearest standard value.

  6. NANO

    Show the colours

    Two digits and a multiplier.

  7. NANO

    Test twenty resistors

    Check against the colour code.

In short

How do you build a resistor value reader?

Clip a resistor in and an Arduino measures it and shows the nearest standard value and colour bands. You need Arduino Nano, Resistor 1 kΩ, Resistor 10 kΩ, Resistor 100 kΩ, SSD1306 OLED Display and Crocodile clip test leads (10 pack). It takes 7 steps and about 90 minutes.

Level
Intermediate
Time
About 90 min
Parts
6

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Reference 1 kΩNano D2 to the test nodeRange one
Reference 10 kΩNano D3 to the test nodeRange two
Reference 100 kΩNano D4 to the test nodeRange three
Test nodeNano A0 and the unknown resistor's clipMeasurement point
Unknown resistor other clipNano GNDReturn
OLED SDA, SCL, VCC, GNDNano A4, A5, 5V, GNDDisplay

Code

A Nano pin set to HIGH is a 5 V source, so one reference resistor to the test node and the unknown one to ground make a voltage divider; the reading says what the ratio is, and the unknown value is the reference times the reading over 1023 minus the reading. A single reference is only accurate near its own value, so the sketch tries the 1 kΩ, then 10 kΩ, then 100 kΩ range, switching the others off by making their pins inputs, and uses the first range that puts the reading between 15 and 85 percent. The result snaps to the nearest standard E24 value and shows the first two colour bands plus the multiplier for a four-band resistor, in colour names. Accuracy depends on the reference resistors; with 1 percent parts, expect about 2 to 3 percent overall, so use it to sort and identify and not for precision. Never connect it to a resistor that is part of a powered circuit. Arduino IDE, board "Arduino Nano" (try the Old Bootloader option if the upload fails).

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// Resistor reader: three reference resistors form a divider with the unknown one. Library: U8g2 (text-only U8x8). Board: Arduino Nano.
#include <U8x8lib.h>
U8X8_SSD1306_128X64_NONAME_HW_I2C oled(U8X8_PIN_NONE);
const int PINS[3] = {2, 3, 4};
const float REF[3] = {1000.0, 10000.0, 100000.0};
const float E24[24] = {1.0,1.1,1.2,1.3,1.5,1.6,1.8,2.0,2.2,2.4,2.7,3.0,3.3,3.6,3.9,4.3,4.7,5.1,5.6,6.2,6.8,7.5,8.2,9.1};
const char* COL[10] = {"Blk","Brn","Red","Org","Yel","Grn","Blu","Vio","Gry","Wht"};
float measure() {
  for (int i = 0; i < 3; i++) {
    for (int k = 0; k < 3; k++) pinMode(PINS[k], INPUT);          // all references off (high impedance)
    pinMode(PINS[i], OUTPUT); digitalWrite(PINS[i], HIGH);
    delay(5);
    long a = 0; for (int s = 0; s < 16; s++) a += analogRead(A0);
    a /= 16;
    if (a > 150 && a < 870) return REF[i] * a / (1023.0 - a);      // this range is accurate: use it
  }
  return -1;
}
void setup() {
  oled.begin(); oled.setFont(u8x8_font_chroma48medium8_r);
}
void loop() {
  float r = measure();
  oled.clear();
  if (r < 0) { oled.drawString(0, 0, "No resistor"); delay(500); return; }
  float mag = pow(10, floor(log10(r)));
  float m = r / mag, best = E24[0]; int bi = 0;
  for (int i = 0; i < 24; i++) if (fabs(E24[i] - m) < fabs(best - m)) { best = E24[i]; bi = i; }
  int d1 = (int)(best), d2 = (int)(best * 10 + 0.5) % 10;
  int mult = (int)(log10(mag) + 0.5) - 1;                                   // 4-band: two digits then a multiplier
  char line[17];
  dtostrf(r, 1, 0, line);
  oled.drawString(0, 0, "Measured ohms:"); oled.drawString(0, 1, line);
  oled.drawString(0, 3, "Nearest E24:");
  dtostrf(best * mag, 1, 0, line); oled.drawString(0, 4, line);
  oled.drawString(0, 6, COL[d1]); oled.drawString(4, 6, COL[d2]);
  oled.drawString(8, 6, mult >= 0 && mult <= 9 ? COL[mult] : "---");
  delay(800);
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
1 kΩ resistorReads about 1000 and brown, black, red
4.7 kΩYellow, violet, red
Nothing clippedShows "No resistor"
SortingMatches the markings within about 3 percent

If it does not work

Value wrong

Check which pin goes to which reference.

Jumpy

Add 100 nF from A0 to ground and average more.

Colours off by a band

Check the multiplier calculation.

No display

Check the OLED wiring and address.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the resistor value reader?

Arduino Nano, Resistor 1 kΩ, Resistor 10 kΩ, Resistor 100 kΩ, SSD1306 OLED Display and Crocodile clip test leads (10 pack).

How long does the resistor value reader take to build?

About 90 minutes for a intermediate maker, in 7 steps.

How do I know the resistor value reader works?

1 kΩ resistor: Reads about 1000 and brown, black, red. 4.7 kΩ: Yellow, violet, red. Nothing clipped: Shows "No resistor".

Value wrong: what should I check?

Check which pin goes to which reference.

Jumpy: what should I check?

Add 100 nF from A0 to ground and average more.

Colours off by a band: what should I check?

Check the multiplier calculation.

No display: what should I check?

Check the OLED wiring and address.