Build it step by step
0 of 7 doneLay out the resistors
Put them in a row with the gold band on the right.
Write your guess
Read the bands and write a value for each.
Measure each one
Note the meter reading next to your guess.
Score yourself
Count the readings within 5 percent of your guess.
Look at the misses
Check whether you swapped the end or confused red and orange.
Repeat against the clock
Mix them up and aim for under 15 seconds a resistor.
Try a friend
Swap sets and compare scores.
How do you build a colour code reading drill?
Read the colour bands on twelve resistors, write down your guess, measure each one with a multimeter and score yourself, then repeat against the clock to build speed and spot the tolerance band. You need Digital multimeter, Resistor 220 Ω, Resistor 1 kΩ, Resistor 10 kΩ, Resistor 4.7 kΩ, Resistor 100 kΩ, Resistor 330 Ω, Resistor 47 kΩ and Resistor 2.2 kΩ. It takes 7 steps and about 40 minutes.
- Level
- Beginner
- Time
- About 40 min
- Parts
- 9
Parts list
- Tools & InstrumentsBuy
- PassivesBuyResistor 220 Ω × 1
- PassivesBuyResistor 1 kΩ × 1
- PassivesBuyResistor 10 kΩ × 1
- PassivesBuyResistor 4.7 kΩ × 1
- PassivesBuyResistor 100 kΩ × 1
- PassivesBuyResistor 330 Ω × 1
- PassivesBuyResistor 47 kΩ × 1
- PassivesBuyResistor 2.2 kΩ × 1
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| Meter red probe (VΩ socket) | One resistor lead | Resistance measurement |
| Meter black probe (COM socket) | The other resistor lead | Resistance measurement |
| Meter dial | The ohms range, or auto | Resistance mode |
| Resistor on a card | Held flat by your fingers away from the probes | Your body adds error if you touch both leads |
No code needed
No code. The first band is the first digit, the second band is the second digit, the third band is how many zeros to add, and the last band, usually gold for 5 percent, is the tolerance. Digits are black 0, brown 1, red 2, orange 3, yellow 4, green 5, blue 6, violet 7, grey 8 and white 9. So 220 ohms is red red brown, 1 kilohm is brown black red, 10 kilohms is brown black orange, 4.7 kilohms is yellow violet red, 100 kilohms is brown black yellow, 330 ohms is orange orange brown, 47 kilohms is yellow violet orange and 2.2 kilohms is red red red. Start reading from the end that is farther from the gold band. Measure each resistor on its own, out of any circuit, and do not hold both leads with your fingers or the reading will be low.
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| Red red brown gold | 220 ohms, 5 percent |
| Brown black red gold | 1 kilohm |
| Brown black orange gold | 10 kilohms |
| Yellow violet red gold | 4.7 kilohms |
| Meter reading | Within 5 percent of the printed value for most resistors |
If it does not work
Reading looks ten times out
You mis-read the multiplier band.
Reading low
Fingers on both leads, or a part in a circuit.
Cannot tell brown from red
Use good light and a white card behind the resistors.
Cannot tell which end to start
Start from the end away from the gold band.
Meter shows 1 or OL
Choose a higher range or check the lead contact.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the colour code reading drill?
Digital multimeter, Resistor 220 Ω, Resistor 1 kΩ, Resistor 10 kΩ, Resistor 4.7 kΩ, Resistor 100 kΩ, Resistor 330 Ω, Resistor 47 kΩ and Resistor 2.2 kΩ.
How long does the colour code reading drill take to build?
About 40 minutes for a beginner maker, in 7 steps.
How do I know the colour code reading drill works?
Red red brown gold: 220 ohms, 5 percent. Brown black red gold: 1 kilohm. Brown black orange gold: 10 kilohms.
Reading looks ten times out: what should I check?
You mis-read the multiplier band.
Reading low: what should I check?
Fingers on both leads, or a part in a circuit.
Cannot tell brown from red: what should I check?
Use good light and a white card behind the resistors.
Cannot tell which end to start: what should I check?
Start from the end away from the gold band.
