Projects / Two-player reaction duel

Two-player reaction duel

Beginner45 minGuided buildReviewed

Build it step by step

0 of 6 done
  1. NANO

    Wire the buttons

    One leg of each button to D2 and D3, the other to GND. The sketch turns on the internal pull-ups.

  2. NANO19.0 mA

    Add the LED

    Anode through 220 Ω to D4, cathode to GND.

  3. NANO12:45

    Add sound and display

    Buzzer to D5 and GND. TM1637 CLK to D6, DIO to D7, power to 5V and GND.

  4. NANO12:45

    Upload

    Install the TM1637 library and upload the sketch.

  5. NANO19.0 mA

    Play a round

    Wait for the LED. The first button wins and the display shows P1 or P2, then the time.

  6. NANO

    Test a false start

    Press early and check the display shows F and the player number.

In short

How do you build a two-player reaction duel?

After a random wait an LED lights and the first player to press their button wins, with the reaction time shown. Pressing early loses. You need Arduino Nano, LED 5 mm red, Resistor 220 Ω, Arcade push button 30 mm × 2, TM1637 4-digit display, Passive buzzer, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 6 steps and about 45 minutes.

Level
Beginner
Time
About 45 min
Parts
8

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Player 1 buttonNano D2 and GNDUses the internal pull-up
Player 2 buttonNano D3 and GNDUses the internal pull-up
Go LED anode through 220 ΩNano D4The signal to react to
Go LED cathodeGNDReturn
Passive buzzer + / −Nano D5 / GNDSounds
TM1637 CLK / DIONano D6 / D7Time display
TM1637 VCC / GNDNano 5V / GNDPower

Code

Arduino IDE, board "Arduino Nano" (processor ATmega328P, or ATmega328P (Old Bootloader) for clones). Install the library "TM1637" by Avishay Orpaz from the Library Manager.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

#include <TM1637Display.h>   // library "TM1637" by Avishay Orpaz

const byte P1 = 2, P2 = 3, LED = 4, BUZ = 5;
TM1637Display disp(6, 7);

void setup() {
  pinMode(P1, INPUT_PULLUP); pinMode(P2, INPUT_PULLUP);
  pinMode(LED, OUTPUT);
  disp.setBrightness(5);
  randomSeed(analogRead(A0));            // an unconnected pin gives noise
}

byte pressed() {                          // 1 or 2 for a player, 0 for none
  if (digitalRead(P1) == LOW) return 1;
  if (digitalRead(P2) == LOW) return 2;
  return 0;
}

void showWho(byte c1, byte player) {
  uint8_t seg[4] = {c1, 0, 0, disp.encodeDigit(player)};
  disp.setSegments(seg);
}

void loop() {
  digitalWrite(LED, LOW);
  uint8_t dash[4] = {0x40, 0x40, 0x40, 0x40};
  disp.setSegments(dash);
  while (pressed()) {}                   // wait until both buttons are released
  delay(500);

  unsigned long wait = random(2000, 6000), t0 = millis();
  while (millis() - t0 < wait) {
    byte p = pressed();
    if (p) {                             // pressed before the LED: this player loses
      tone(BUZ, 200, 400);
      showWho(0x71, p);                  // F and the player number
      delay(2500);
      return;
    }
  }

  digitalWrite(LED, HIGH);
  unsigned long start = micros();
  byte p = 0;
  while (!(p = pressed())) {}
  unsigned long ms = (micros() - start) / 1000;
  digitalWrite(LED, LOW);
  tone(BUZ, 1500, 150);
  showWho(0x73, p);                      // P and the winner
  delay(1500);
  disp.showNumberDec(ms);                // the winning time in milliseconds
  delay(3500);
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Wait for the LED, then pressDisplay shows P and the player number, then a time such as 245
Press before the LEDA low beep and F with the player number
Press at the same timeThe player checked first (player 1) wins, which is fine for a game
Typical timesMost people are between 180 and 350 ms

If it does not work

The LED never lights

Check its direction and that its resistor goes to D4.

A press is never detected

Buttons must go between the pin and GND, and the sketch uses INPUT_PULLUP.

The display stays blank

Check CLK and DIO are on D6 and D7 and the library is installed.

Times always show 0

A button is stuck closed. Check wiring and that you released both before the round.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the two-player reaction duel?

Arduino Nano, LED 5 mm red, Resistor 220 Ω, Arcade push button 30 mm × 2, TM1637 4-digit display, Passive buzzer, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm).

How long does the two-player reaction duel take to build?

About 45 minutes for a beginner maker, in 6 steps.

How do I know the two-player reaction duel works?

Wait for the LED, then press: Display shows P and the player number, then a time such as 245. Press before the LED: A low beep and F with the player number. Press at the same time: The player checked first (player 1) wins, which is fine for a game.

The LED never lights: what should I check?

Check its direction and that its resistor goes to D4.

A press is never detected: what should I check?

Buttons must go between the pin and GND, and the sketch uses INPUT_PULLUP.

The display stays blank: what should I check?

Check CLK and DIO are on D6 and D7 and the library is installed.

Times always show 0: what should I check?

A button is stuck closed. Check wiring and that you released both before the round.