Rain alert for the clothesline
Build it step by step
0 of 5 donePlace the plate
Fix the sensing plate tilted at about 30° outside, so drops land on it and run off.
Run the cable
Carry the two plate wires indoors on the shielded cable to the control module.
Wire the module
VCC to D4, GND to GND, AO to A0, DO to D5.
Add the alert
Buzzer on D8, blue LED with 220 Ω on D9.
Set the trimmer
Upload, sprinkle a few drops on the plate and turn the module trimmer until its DO LED lights with a few drops.
How do you build a rain alert for the clothesline?
A rain sensor plate on the balcony beeps a buzzer indoors at the first drops, so the washing comes in on time. You need Arduino Nano, Rain drop sensor module, Active buzzer 5 V, LED 5 mm blue, Resistor 220 Ω, Multi-core shielded cable 4-core, 5 V 2 A USB adapter and USB A to micro-USB cable (data). It takes 5 steps and about 40 minutes.
- Level
- Beginner
- Time
- About 40 min
- Parts
- 8
Parts list
- Development BoardsBuyArduino Nano × 1
- SensorsBuy
- Motors & ActuatorsBuy
- OptoelectronicsBuyLED 5 mm blue × 1
- PassivesBuyResistor 220 Ω × 1
- Cables & WiresUp to 5 m from balcony to indoors
- PowerBuy
- Cables & WiresBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| Rain board | Control module (two short wires) | Sensing plate outside, module indoors |
| Module VCC / GND | Nano D4 / GND | Power only while reading, so the plate corrodes slower |
| Module AO | Nano A0 | Wetness (lower = wetter) |
| Module DO | Nano D5 | LOW when wet past the trimmer setting |
| Nano D8 | Buzzer + (− to GND) | Alert |
| Nano D9 | 220 Ω, blue LED, GND | Rain light |
Code
Arduino IDE, board "Arduino Nano" (choose "ATmega328P (Old Bootloader)" for most clones). No extra libraries.
Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).
const int POWER = 4, WET_PIN = 5, LEVEL = A0, BUZZER = 8, LED = 9;
void setup() {
pinMode(POWER, OUTPUT); pinMode(WET_PIN, INPUT);
pinMode(BUZZER, OUTPUT); pinMode(LED, OUTPUT);
Serial.begin(9600);
}
void loop() {
digitalWrite(POWER, HIGH); delay(20); // power the plate only while reading
int level = analogRead(LEVEL);
bool wet = digitalRead(WET_PIN) == LOW;
digitalWrite(POWER, LOW);
Serial.print("level="); Serial.print(level); Serial.println(wet ? " RAIN" : "");
digitalWrite(LED, wet);
if (wet) {
for (int i = 0; i < 3; i++) { digitalWrite(BUZZER, HIGH); delay(150); digitalWrite(BUZZER, LOW); delay(150); }
}
delay(2000);
}What the serial monitor should show
Open the serial monitor at the baud rate in the code. This is what our simulator prints for a virtual Arduino Nano with its sensors at their default values. Your numbers will follow your real readings, but the format should match.
level=205 RAIN level=206 RAIN level=205 RAIN
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| Dry plate | level 900 to 1023, no beeps |
| A few drops | level falls below about 700, blue LED and three beeps every 2 s |
| Plate wiped dry | Alerts stop within a few seconds |
If it does not work
Always says rain
Turn the module trimmer the other way, or dry the plate.
Never says rain
Check the plate wires reach the module and DO goes to D5.
The plate turns green over weeks
That is corrosion. Powering it only while reading (as here) slows it. Replace the plate when it gets bad.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the rain alert for the clothesline?
Arduino Nano, Rain drop sensor module, Active buzzer 5 V, LED 5 mm blue, Resistor 220 Ω, Multi-core shielded cable 4-core, 5 V 2 A USB adapter and USB A to micro-USB cable (data). Multi-core shielded cable 4-core: Up to 5 m from balcony to indoors.
How long does the rain alert for the clothesline take to build?
About 40 minutes for a beginner maker, in 5 steps.
How do I know the rain alert for the clothesline works?
Dry plate: level 900 to 1023, no beeps. A few drops: level falls below about 700, blue LED and three beeps every 2 s. Plate wiped dry: Alerts stop within a few seconds.
Always says rain: what should I check?
Turn the module trimmer the other way, or dry the plate.
Never says rain: what should I check?
Check the plate wires reach the module and DO goes to D5.
The plate turns green over weeks: what should I check?
That is corrosion. Powering it only while reading (as here) slows it. Replace the plate when it gets bad.
