Projects / Solar lantern

Solar lantern

Beginner1.5 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. SOLAR

    Test the panel

    Measure open-circuit voltage in sun (about 6 V or more).

  2. CN306517.5 mA

    Connect the charger

    Check the charging LED lights.

  3. +

    Add the cell

    Check BAT+ polarity before inserting the cell.

  4. 17.5 mA

    Add the LED and the resistor

    Check the current with a multimeter.

  5. 754 lux

    Add the dusk switch

    Test with a shaded LDR.

  6. CN3065+

    Add the cut-off

    Fit a protection board.

  7. Test two cloudy days

    Note how long it lasts.

In short

How do you build a solar lantern?

A small panel, a cell and an LED make a lantern that works all night. You need Solar panel 6 V 1 W, CN3065 solar Li-ion charger module, 18650 Li-ion cell, Battery holder 18650 single, High-power LED 1 W white (star), BC547 NPN transistor, LDR Photoresistor, Resistor 10 kΩ and Resistor 1 kΩ. It takes 7 steps and about 90 minutes.

Level
Beginner
Time
About 90 min
Parts
9

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Solar panel + and −CN3065 module IN+ and IN−Charger input
CN3065 BAT+ and BAT−18650 holder + and −Cell charging
Cell +LED star anodeLED supply (through the current limit, see notes)
LED cathodeBC547 collector, emitter to GNDSwitch
LDR and 10 kΩ divider from panel + to GNDBC547 base through 1 kΩ,Dusk switch (LED on when the panel voltage is low)

No code needed

The CN3065 module charges one lithium cell from a small solar panel. A 1 W white LED star needs a current limit: add a small resistor in series (a few ohms, 1 W) chosen so that the current stays about 100 to 200 mA from a 3.7 V cell, and check with a multimeter in series before closing the case. The simple dusk switch here turns the LED on when the divider output falls in the dark; set the response with the divider values and test at dusk. Use a protected 18650 cell or a protection board, never charge an unprotected cell without a proper charger, and never short the cell. Do not run it from the cell down to zero. Add a cut-off at about 3.2 V, for example a small battery protection board between the cell and the LED, so that the cell is not damaged. Keep the panel facing the sun and the cell out of direct heat; do not leave a cell in a hot closed box. This build uses a lithium cell safely only within these limits, so if you are unsure, use a ready protected solar charger board.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Panel in the sunCharger LED shows charging
Panel in the shadeLED lights up
Cell at 3.0 VThe cut-off stops the LED
Two cloudy daysStill lights for several hours

If it does not work

Does not charge

Check polarity and that the panel gives over 5 V in sun.

LED too dim

Reduce the series resistor a little and check the current.

LED on in daylight

Swap the LDR and the 10 kΩ resistor.

Cell gets warm

Disconnect and check for a short.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the solar lantern?

Solar panel 6 V 1 W, CN3065 solar Li-ion charger module, 18650 Li-ion cell, Battery holder 18650 single, High-power LED 1 W white (star), BC547 NPN transistor, LDR Photoresistor, Resistor 10 kΩ and Resistor 1 kΩ.

How long does the solar lantern take to build?

About 90 minutes for a beginner maker, in 7 steps.

How do I know the solar lantern works?

Panel in the sun: Charger LED shows charging. Panel in the shade: LED lights up. Cell at 3.0 V: The cut-off stops the LED.

Does not charge: what should I check?

Check polarity and that the panel gives over 5 V in sun.

LED too dim: what should I check?

Reduce the series resistor a little and check the current.

LED on in daylight: what should I check?

Swap the LDR and the 10 kΩ resistor.

Cell gets warm: what should I check?

Disconnect and check for a short.