Projects / Persistence-of-vision wand

Persistence-of-vision wand

Beginner2.5 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. NANO18.1 mA

    Wire the LEDs

    Each long leg through 220 ohms to D2 up to D9, all short legs to GND.

  2. NANO18.1 mA

    Arrange the LEDs

    In a straight line on the stick, LED 1 at the top.

  3. NANO

    Wire the tilt switch

    D10 to GND.

  4. NANO18.1 mA

    Upload the sketch

    The LEDs stay off.

  5. NANO

    Wave the wand side to side in the dark

    The letters appear in the air.

  6. NANO

    Tune COLUMN_US

    Smaller for a fast wave, larger for a slow wave.

  7. NANO

    Fix the Nano and a power bank to the stick

    So it works without the computer.

In short

How do you build a persistence-of-vision wand?

Eight LEDs on a stick flash a column of a message each fraction of a second, so when the wand is waved the message appears hanging in the air. A tilt switch starts the display. You need Arduino Nano, LED 5 mm red × 8, Resistor 220 Ω × 8, Tilt sensor (ball switch, SW-520D), Jumper wires male to male (40 pcs, 20 cm) and Breadboard 830 Tie Points. It takes 7 steps and about 150 minutes.

Level
Beginner
Time
About 150 min
Parts
6

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
LED 1 (top) long leg220 ohm resistor to Nano D2Top row of the letters
LED 2 long leg220 ohm resistor to Nano D3Row 2
LED 3 long leg220 ohm resistor to Nano D4Row 3
LED 4 long leg220 ohm resistor to Nano D5Row 4
LED 5 long leg220 ohm resistor to Nano D6Row 5
LED 6 long leg220 ohm resistor to Nano D7Row 6
LED 7 long leg220 ohm resistor to Nano D8Row 7
LED 8 (bottom) long leg220 ohm resistor to Nano D9Spare row
All LED short legsNano GNDCommon return
Tilt switchNano D10 and GNDStarts the message when the wand moves

Code

Persistence of vision means the eye keeps an image for a fraction of a second after it has gone. If a row of LEDs flashes a different pattern each few thousandths of a second while it moves through the air, the patterns line up side by side in the eye, and a message seems to hang in space. Each letter is stored as five columns of seven dots, and the program sends each column to the eight LEDs in turn, with a short blank between letters. The tilt switch has a small ball inside that rolls when the wand is swung, and each time it changes state a new sweep of the message starts, with a short lockout so that it does not restart in the middle. The speed of your wave decides how wide the letters look, so change the column time until the letters are readable, smaller for a fast wave. Read the message in a dim room, and wave the wand in a clear space away from people and furniture. Make the wand from a light stick and do not make it heavy. Use only LEDs with a resistor each, never the LEDs directly on the pins. Add more letters to the font table, using the same five-byte format, for other words.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

const uint8_t LED_PINS[8] = { 2, 3, 4, 5, 6, 7, 8, 9 };
const int TILT = 10;
const unsigned int COLUMN_US = 2500;               // time each column is lit: tune to your wave speed
const unsigned int GAP_US = 2500;                  // blank gap between letters

// 5 by 7 letters, one byte per column, bit 0 is the top row
struct Glyph { char ch; uint8_t col[5]; };
const Glyph FONT[] = {
  { 'A', { 0x7E, 0x11, 0x11, 0x11, 0x7E } },
  { 'C', { 0x3E, 0x41, 0x41, 0x41, 0x22 } },
  { 'E', { 0x7F, 0x49, 0x49, 0x49, 0x41 } },
  { 'K', { 0x7F, 0x08, 0x14, 0x22, 0x41 } },
  { 'L', { 0x7F, 0x40, 0x40, 0x40, 0x40 } },
  { 'O', { 0x3E, 0x41, 0x41, 0x41, 0x3E } },
  { 'R', { 0x7F, 0x09, 0x19, 0x29, 0x46 } },
  { 'T', { 0x01, 0x01, 0x7F, 0x01, 0x01 } },
};
const char MESSAGE[] = "ELECTROLARK";               // use only letters that are in FONT
bool lastTilt;
unsigned long lockoutUntil = 0;

void showColumn(uint8_t bits) {
  for (int i = 0; i < 8; i++) digitalWrite(LED_PINS[i], (bits >> i) & 1);
}

const Glyph* find(char c) {
  for (unsigned int i = 0; i < sizeof(FONT) / sizeof(FONT[0]); i++)
    if (FONT[i].ch == c) return &FONT[i];
  return nullptr;
}

void playMessage() {
  for (const char* p = MESSAGE; *p; p++) {
    const Glyph* g = find(*p);
    if (g) {
      for (int c = 0; c < 5; c++) {
        showColumn(g->col[c]);
        delayMicroseconds(COLUMN_US);
      }
    }
    showColumn(0);
    delayMicroseconds(GAP_US);
  }
  showColumn(0);
}

void setup() {
  for (int i = 0; i < 8; i++) pinMode(LED_PINS[i], OUTPUT);
  pinMode(TILT, INPUT_PULLUP);
  lastTilt = digitalRead(TILT);
  showColumn(0);
}

void loop() {
  bool t = digitalRead(TILT);
  if (t != lastTilt && millis() > lockoutUntil) {  // the ball moved: a sweep has started
    playMessage();
    lockoutUntil = millis() + 300;                 // ignore the rattle for a moment
  }
  lastTilt = t;
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Hold stillLEDs off
Shake gentlyA burst of letters starts
Wave in a dim roomELECTROLARK appears in the air
Wave fasterLetters look narrower
Change COLUMN_USLetters change width

If it does not work

Letters look mirrored

Wave the other way, or reverse the column order.

Nothing shows

Check the tilt switch wires and that it changes when shaken.

One LED dark

Check the leg direction and the resistor.

Letters upside down

Put LED 1 at the other end of the stick.

Restarts in the middle

Lengthen the lockout time.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the persistence-of-vision wand?

Arduino Nano, LED 5 mm red × 8, Resistor 220 Ω × 8, Tilt sensor (ball switch, SW-520D), Jumper wires male to male (40 pcs, 20 cm) and Breadboard 830 Tie Points.

How long does the persistence-of-vision wand take to build?

About 150 minutes for a beginner maker, in 7 steps.

How do I know the persistence-of-vision wand works?

Hold still: LEDs off. Shake gently: A burst of letters starts. Wave in a dim room: ELECTROLARK appears in the air.

Letters look mirrored: what should I check?

Wave the other way, or reverse the column order.

Nothing shows: what should I check?

Check the tilt switch wires and that it changes when shaken.

One LED dark: what should I check?

Check the leg direction and the resistor.

Letters upside down: what should I check?

Put LED 1 at the other end of the stick.