Projects / Motion night light

Motion night light

Beginner1 hGuided buildReviewed

Build it step by step

0 of 8 done
  1. UNOmotion

    Wire the PIR

    VCC to 5V, GND to GND, OUT to D2.

  2. UNO558 lux

    Wire the light sensor

    LDR from 5V to A0, 10 kilohm from A0 to GND.

  3. UNO14.6 mA

    Wire the LEDs

    Each through 330 ohm on D9, D10 and D11.

  4. UNOmotion

    Turn the PIR delay screw

    To its lowest setting.

  5. UNO

    Upload the sketch and wait

    Thirty seconds for the sensor to settle.

  6. UNO561 lux

    Cover the LDR and wave a hand

    The LEDs fade in.

  7. UNO

    Stay still

    They fade out after a minute.

  8. UNO14.6 mA

    Try in a bright room

    The LEDs stay off.

In short

How do you build a motion night light?

A PIR sensor turns on a soft night light for a minute when someone walks past in the dark. You need Arduino Uno R3, PIR Motion Sensor HC-SR501, LDR Photoresistor, Resistor 10 kΩ, LED 5 mm white × 3, Resistor 330 Ω × 3, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 8 steps and about 60 minutes.

Level
Beginner
Time
About 60 min
Parts
8

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
PIR VCCUno 5VPower
PIR GNDUno GNDGround
PIR OUTUno D2High when motion is seen
LDR one legUno 5VTop of the light divider
LDR other leg and 10 kilohmUno A0Divider midpoint, 10 kilohm goes to GND
White LED 1 through 330 ohmUno D9 to GNDNight light
White LED 2 through 330 ohmUno D10 to GNDNight light
White LED 3 through 330 ohmUno D11 to GNDNight light

Code

A passive infrared sensor notices the change in heat when a warm body moves across its view, and its output goes high. On its own it would switch a light on in daytime too, so a light sensor makes it useful: the LDR and the 10 kilohm resistor form a divider whose voltage rises as the room gets brighter, and the light only comes on when the reading is below a threshold. The light stays on for a minute after the last motion and fades in and out smoothly using PWM, which looks gentler than a sudden switch. Three LEDs on three pins, each with its own resistor, keep every pin well within its current limit. The HC-SR501 has two small screws: one sets how long its own output stays high and one sets sensitivity; turn the delay to the minimum so the sketch controls the timing. It needs about 30 seconds after power on to settle, which the sketch waits for. Mount it facing a doorway, away from heaters or sunny windows, which can cause false triggers.

Runs on a virtual Arduino Uno in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

const int PIR = 2;
const int LDR = A0;
const int LEDS[] = {9, 10, 11};
const int DARK_BELOW = 350;                // 0 to 1023, higher means brighter, tune for your room
const unsigned long HOLD_MS = 60000;       // stay on for 60 seconds after the last motion

unsigned long lastMotion = 0;
int level = 0;                             // current brightness 0 to 255
bool lit = false;

void setLeds(int v) {
  for (int i = 0; i < 3; i++) analogWrite(LEDS[i], v);
}

void setup() {
  pinMode(PIR, INPUT);
  for (int i = 0; i < 3; i++) pinMode(LEDS[i], OUTPUT);
  Serial.begin(9600);
  delay(30000);                            // the PIR needs about 30 seconds to settle
}

void loop() {
  int light = analogRead(LDR);
  bool dark = (light < DARK_BELOW);

  if (digitalRead(PIR) == HIGH && dark) {
    lastMotion = millis();
    lit = true;
  }
  if (lit && (millis() - lastMotion > HOLD_MS || !dark)) lit = false;

  int target = lit ? 200 : 0;              // keep it soft, not full brightness
  if (level < target) level += 4;          // fade in
  if (level > target) level -= 2;          // fade out slowly
  level = constrain(level, 0, 255);
  setLeds(level);

  Serial.print(light); Serial.print(' ');
  Serial.println(lit ? "on" : "off");
  delay(20);
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Dark and motionLight fades in
No more motionOff after 60 seconds
Bright room and motionStays off
Light turns on while litSwitches off
First 30 secondsNo response while settling

If it does not work

Light never comes on

Lower the room light or raise DARK_BELOW.

Comes on in daylight

Lower DARK_BELOW, check the LDR divider.

Random triggers

Move away from heat sources and shield from sunlight.

Light stays on forever

The PIR delay screw is too high, turn it down.

LEDs flicker

Check connections on D9, D10 and D11.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the motion night light?

Arduino Uno R3, PIR Motion Sensor HC-SR501, LDR Photoresistor, Resistor 10 kΩ, LED 5 mm white × 3, Resistor 330 Ω × 3, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm).

How long does the motion night light take to build?

About 60 minutes for a beginner maker, in 8 steps.

How do I know the motion night light works?

Dark and motion: Light fades in. No more motion: Off after 60 seconds. Bright room and motion: Stays off.

Light never comes on: what should I check?

Lower the room light or raise DARK_BELOW.

Comes on in daylight: what should I check?

Lower DARK_BELOW, check the LDR divider.

Random triggers: what should I check?

Move away from heat sources and shield from sunlight.

Light stays on forever: what should I check?

The PIR delay screw is too high, turn it down.