Projects / Pico knob-controlled servo

Pico knob-controlled servo

Intermediate2 hGuided buildReviewed

Build it step by step

0 of 6 done
  1. PICO

    Wire the knob

    Outer legs to 3V3(OUT) and GND, wiper to GP26.

  2. PICO59°

    Wire the servo

    Signal to GP16, power from the separate supply, grounds joined.

  3. PICO

    Save the program as main.py

    On the Pico.

  4. PICO59°

    Run it

    The servo goes to the middle.

  5. PICO59°

    Turn the knob

    The servo follows.

  6. PICO59°

    Change the limits

    Find the safe ends for your servo.

In short

How do you build a pico knob-controlled servo?

A Pico moves a hobby servo with a knob, using hardware PWM at 50 Hz from MicroPython, with the servo on its own supply. You need Raspberry Pi Pico H, SG90 Micro Servo, Potentiometer 10 kΩ and Breadboard 830 Tie Points. It takes 6 steps and about 120 minutes.

Level
Intermediate
Time
About 120 min
Parts
4

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Pot outer legsPico 3V3(OUT) pin 36 and GNDVoltage divider
Pot wiperPico GP26 pin 31 (ADC0)Analog input
Servo signal (orange or yellow)Pico GP16 pin 21PWM output
Servo power (red)Separate 5 V supply, not the PicoA servo can pull hundreds of milliamps
Servo ground (brown or black)Supply ground and Pico GNDCommon ground

Code

A hobby servo expects a pulse every 20 milliseconds, which is 50 hertz, and the width of the pulse sets the angle: about 1 ms for one end, 1.5 ms for the middle and 2 ms for the other end. The Pico makes these pulses with a hardware PWM block that counts on its own, so the arm stays steady while the program does other work. In MicroPython the duty is a 16-bit number, so a pulse of a given width is that width divided by the 20 ms period, times 65535. The knob is read with the ADC and smoothed a little so the arm does not shake. Small servos accept the 3.3 V signal, but the servo itself must have its own 5 V supply, since a moving servo can draw far more current than the Pico USB socket should give. The grounds of the supply and the Pico must be joined. If the arm buzzes at the ends, narrow the pulse limits a little.

import time
from machine import Pin, PWM, ADC

pot = ADC(26)
servo = PWM(Pin(16))
servo.freq(50)                                   # one pulse every 20 ms

MIN_US, MAX_US = 1000, 2000                      # pulse width range in microseconds

def set_pulse(us):
    servo.duty_u16(int(us * 65535 / 20000))      # fraction of the 20 ms period

smooth = pot.read_u16()
while True:
    smooth = int(0.9 * smooth + 0.1 * pot.read_u16())   # gentle smoothing
    us = MIN_US + (MAX_US - MIN_US) * smooth // 65535
    set_pulse(us)
    time.sleep_ms(20)

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Knob in the middleServo near the centre
Knob to one endServo moves to one limit
Knob to the other endServo moves to the other limit
Knob moved slowlySmooth movement
Servo on its own supplyPico does not reset when the servo moves

If it does not work

Servo twitches or the Pico resets

Power the servo from its own 5 V supply and join the grounds.

Servo does not move

Check GP16 and the signal wire colour.

Servo hums at the ends

Reduce MIN_US and MAX_US slightly.

Jittery movement

Add a 100 nanofarad capacitor from GP26 to GND.

Program does not start on power-up

Save it on the Pico as main.py.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the pico knob-controlled servo?

Raspberry Pi Pico H, SG90 Micro Servo, Potentiometer 10 kΩ and Breadboard 830 Tie Points.

How long does the pico knob-controlled servo take to build?

About 120 minutes for a intermediate maker, in 6 steps.

How do I know the pico knob-controlled servo works?

Knob in the middle: Servo near the centre. Knob to one end: Servo moves to one limit. Knob to the other end: Servo moves to the other limit.

Servo twitches or the Pico resets: what should I check?

Power the servo from its own 5 V supply and join the grounds.

Servo does not move: what should I check?

Check GP16 and the signal wire colour.

Servo hums at the ends: what should I check?

Reduce MIN_US and MAX_US slightly.

Jittery movement: what should I check?

Add a 100 nanofarad capacitor from GP26 to GND.