Projects / Pico N20 motor speed knob

Pico N20 motor speed knob

Beginner2 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. PICO

    Mount the motor

    Fix it in its bracket and the bracket to the board or a table.

  2. PICO

    Wire the knob

    Ends to 3V3(OUT) and GND, middle to GP26.

  3. PICOTIP120

    Wire the transistor

    Base through 1 kilo-ohm to GP15, emitter to GND, collector to the motor.

  4. PICO

    Wire the motor supply

    Other motor wire to VBUS pin 40.

  5. PICO

    Add the diode

    Across the motor, stripe towards VBUS.

  6. PICO

    Run the program

    The shell shows the speed in percent.

  7. PICO

    Turn the knob

    Slowly up, the motor starts and speeds up.

In short

How do you build a pico N20 motor speed knob?

A Pico drives a small N20 geared motor on a mounting bracket through a TIP120 transistor with a flyback diode, and a potentiometer sets the speed with PWM. You need Raspberry Pi Pico H, N20 micro metal gear motor, Motor mount bracket (N20 / BO), TIP120 Darlington transistor, Resistor 1 kΩ, Signal Diode 1N4148, Potentiometer 10 kΩ and Breadboard 830 Tie Points. It takes 7 steps and about 120 minutes.

Level
Beginner
Time
About 120 min
Parts
8

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Potentiometer endsPico 3V3(OUT) pin 36 and GND pin 38Knob across 3.3 V
Potentiometer middlePico GP26 pin 31ADC0 input
Pico GP15 pin 201 kilo-ohm resistor to TIP120 base (left pin, flat side towards you)PWM control signal
TIP120 emitter (right pin)Pico GND pin 38Common ground for motor and Pico
TIP120 collector (middle pin)Motor wire 2Switches the motor to ground
Motor wire 1Pico VBUS pin 40 (5 V from USB)Motor supply
1N4148 diodeAcross the motor, stripe (cathode) on the VBUS sideFlyback diode absorbs the voltage spike

Code

A small motor needs more current than a Pico pin can give, so the pin only controls a transistor and the transistor carries the motor current. The TIP120 is a Darlington transistor, two transistors in one, so a few milliamps into its base can switch an amp. A 1 kilo-ohm resistor limits the base current. PWM, pulse-width modulation, switches the motor on and off a thousand times a second and the fraction of time it is on sets the average power and so the speed. A motor is a coil, and when the current is cut the coil pushes out a spike of voltage. The 1N4148 diode across the motor gives that spike a path so it does not damage the transistor. The diode must be the right way round, with its stripe towards the positive supply. The program reads the knob eight times and averages it, leaves a small dead zone at the bottom so the motor can be fully off, and skips the low duty values at which a motor only hums. The TIP120 drops about a volt, so the motor runs a little slower than its rating. Power the motor from a USB port that can supply enough current and do not hold the shaft, because a stalled motor draws much more. Keep wires clear of the gears.

from machine import Pin, PWM, ADC
import time

motor = PWM(Pin(15))
motor.freq(1000)                                    # 1 kHz is quiet enough for a small motor
knob = ADC(26)

MIN_START = 18000                                   # below this duty the motor only hums, so jump over it

def duty_for(reading):
    if reading < 3000:                              # a dead zone at the bottom so the motor can be fully off
        return 0
    span = 65535 - MIN_START
    return int(MIN_START + (reading - 3000) * span / (65535 - 3000))

last_percent = -1
while True:
    total = 0
    for _ in range(8):
        total += knob.read_u16()
    reading = total // 8
    duty = duty_for(reading)
    motor.duty_u16(duty)
    percent = duty * 100 // 65535
    if percent != last_percent:
        print("Speed", percent, "%")
        last_percent = percent
    time.sleep_ms(30)

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Knob fully leftMotor off, speed 0
Turn slowly rightMotor starts, then gets faster
Knob fully rightTop speed
Turn back leftSlows to a stop
Touch the transistor after a minuteOnly slightly warm

If it does not work

Motor does not turn

Check the transistor pins (base, collector, emitter) against its datasheet.

Motor only hums at low speed

Normal, the program skips the lowest duty.

Pico resets when the motor starts

Use a better USB port or cable, or power the motor from a separate supply with a common ground.

Transistor gets hot

Make sure it is fully switched on and the motor is not stalled.

Speed jumps around

Check the knob wiring and keep wires short.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the pico N20 motor speed knob?

Raspberry Pi Pico H, N20 micro metal gear motor, Motor mount bracket (N20 / BO), TIP120 Darlington transistor, Resistor 1 kΩ, Signal Diode 1N4148, Potentiometer 10 kΩ and Breadboard 830 Tie Points.

How long does the pico N20 motor speed knob take to build?

About 120 minutes for a beginner maker, in 7 steps.

How do I know the pico N20 motor speed knob works?

Knob fully left: Motor off, speed 0. Turn slowly right: Motor starts, then gets faster. Knob fully right: Top speed.

Motor does not turn: what should I check?

Check the transistor pins (base, collector, emitter) against its datasheet.

Motor only hums at low speed: what should I check?

Normal, the program skips the lowest duty.

Pico resets when the motor starts: what should I check?

Use a better USB port or cable, or power the motor from a separate supply with a common ground.

Transistor gets hot: what should I check?

Make sure it is fully switched on and the motor is not stalled.