Projects / Pi melody doorbell button

Pi melody doorbell button

A Raspberry Pi 4 plays a short tune on a passive buzzer when a button is pressed, and a different tune on a long press.

Beginner1.8 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. Pi 4

    Shut the Pi down

    Then unplug power.

  2. Pi 4

    Wire the buzzer

    Pin 12 through 330 ohms, minus to pin 14.

  3. Pi 4

    Wire the button

    Pin 11 to pin 9.

  4. Pi 4

    Boot and run the program

    Nothing sounds yet.

  5. Pi 4

    Press the button briefly

    Tune one plays.

  6. Pi 4

    Hold it for a second

    Tune two plays.

  7. Pi 4

    Add your own tune

    Write a new list and call play with it.

In short

How do you build a pi melody doorbell button?

A Raspberry Pi 4 plays a short tune on a passive buzzer when a button is pressed, and a different tune on a long press. You need Raspberry Pi 4 Model B (4 GB), Passive buzzer, Tactile push button 6 mm, Resistor 330 Ω and Breadboard 830 Tie Points. It takes 7 steps and about 110 minutes.

Level
Beginner
Time
About 110 min
Parts
5

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Passive buzzer plus330 ohm resistor to Pi pin 12 (GPIO18)Tone output
Passive buzzer minusPi pin 14 (GND)Return
ButtonPi pin 11 (GPIO17) and pin 9 (GND)Short press for tune one, long press for tune two

Code

A tune is a list of pitches and lengths. Each note here is a frequency in hertz and a time in seconds, stored in a list, and the player sounds each one for most of its time with a short silent gap so repeated notes can be heard apart. A passive buzzer has no tone circuit of its own, so the Pi must supply the tone, and the gpiozero library does this with a PWM signal on the pin set to the note frequency. The PWM is made in software, so the pitch may wobble a little when the Pi is busy, which is fine for a doorbell. The button uses the Pi internal pull-up resistor, so one side goes to the pin and the other to ground. The program measures how long the button is held, and a press of 0.8 seconds or more plays the second tune. The 330 ohm resistor limits the pin current. Keep the volume modest and the buzzer away from your ear.

from gpiozero import Button, TonalBuzzer
from gpiozero.tones import Tone
from time import sleep, time

buzzer = TonalBuzzer(18)
button = Button(17)                              # internal pull-up, pressed connects to ground

C4, D4, E4, F4, G4, A4 = 262, 294, 330, 349, 392, 440

# Each note is (frequency in hertz, length in seconds)
ODE = [(E4,.4),(E4,.4),(F4,.4),(G4,.4),(G4,.4),(F4,.4),(E4,.4),(D4,.4),
       (C4,.4),(C4,.4),(D4,.4),(E4,.4),(E4,.6),(D4,.2),(D4,.8)]
TWINKLE = [(C4,.4),(C4,.4),(G4,.4),(G4,.4),(A4,.4),(A4,.4),(G4,.8),
           (F4,.4),(F4,.4),(E4,.4),(E4,.4),(D4,.4),(D4,.4),(C4,.8)]

def play(tune):
    for freq, length in tune:
        buzzer.play(Tone(frequency=freq))
        sleep(length * 0.9)
        buzzer.stop()
        sleep(length * 0.1)                      # short gap so repeated notes are heard

while True:
    button.wait_for_press()
    start = time()
    button.wait_for_release()
    held = time() - start
    play(TWINKLE if held >= 0.8 else ODE)

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Short pressTune one plays in full
Long pressTune two plays
Repeated notesHeard as separate notes
PitchRises and falls as in the tune
No pressSilence

If it does not work

No sound

Check the buzzer is passive and wired to pin 12.

Out of range error

TonalBuzzer limits notes to about C3 to B6, adjust the numbers.

Notes wobble

Close other programs, software PWM depends on the load.

Long press not recognised

Hold for a full second.

Button does nothing

Check pin 11 and ground.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the pi melody doorbell button?

Raspberry Pi 4 Model B (4 GB), Passive buzzer, Tactile push button 6 mm, Resistor 330 Ω and Breadboard 830 Tie Points.

How long does the pi melody doorbell button take to build?

About 110 minutes for a beginner maker, in 7 steps.

How do I know the pi melody doorbell button works?

Short press: Tune one plays in full. Long press: Tune two plays. Repeated notes: Heard as separate notes.

No sound: what should I check?

Check the buzzer is passive and wired to pin 12.

Out of range error: what should I check?

TonalBuzzer limits notes to about C3 to B6, adjust the numbers.

Notes wobble: what should I check?

Close other programs, software PWM depends on the load.

Long press not recognised: what should I check?

Hold for a full second.