Projects / Noise trend logger

Noise trend logger

Intermediate55 minGuided buildReviewed
ESP32 DevKitGPIO34GPIO5GPIO18GPIO23GPIO19MAX4466Loudnessminute,avg,peak12,420,420noise.csv
Serial at 115200 baud

Tap a part to see what it does.

Tap the parts to see what each one does. A teaching simulation, not a circuit simulator.

Build it step by step

0 of 4 done
  1. ESP32MAX4466

    Wire the microphone

    VCC to 3V3, OUT to GPIO34.

  2. ESP32

    Wire the SD module

    CS 5, SCK 18, MOSI 23, MISO 19.

  3. ESP32MICROS

    Format the card

    FAT32, then insert it.

  4. ESP32

    Upload and leave it

    Let it run for an hour, then open noise.csv in a spreadsheet.

In short

How do you build a noise trend logger?

An ESP32 measures loudness from a MAX4466 microphone every 50 ms and writes the average and peak for each minute to a microSD card. You need ESP32 DevKit V1, MAX4466 microphone module, MicroSD Card Module and Breadboard 830 Tie Points. It takes 4 steps and about 55 minutes.

Level
Intermediate
Time
About 55 min
Parts
4

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Mic VCC / GNDESP32 3V3 / GNDPower (3.3 V keeps the output in ADC range)
Mic OUTGPIO34Audio
SD CS / SCK / MOSI / MISOGPIO5 / 18 / 23 / 19SPI
SD VCC / GND5V (VIN) / GNDPower for a 5 V module

Code

Built-in SD library for ESP32. Values are relative (ADC counts), not decibels. Turn the gain trimmer until normal talking reads about 300 to 800.

Runs on a virtual ESP32 Dev Module in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

#include <SD.h>
const int MIC = 34, CS = 5;
long total = 0; int samples = 0, peak = 0;
unsigned long minuteStart = 0;

int window() {
  int lo = 4095, hi = 0; unsigned long t = millis();
  while (millis() - t < 50) { int v = analogRead(MIC); lo = min(lo, v); hi = max(hi, v); }
  return hi - lo;
}

void setup() {
  Serial.begin(115200);
  if (!SD.begin(CS)) Serial.println("SD card not found");
  File f = SD.open("/noise.csv", FILE_APPEND);
  if (f) { f.println("minute,average,peak"); f.close(); }
}

void loop() {
  int p = window();
  total += p; samples++; peak = max(peak, p);
  if (millis() - minuteStart >= 60000) {
    int avg = total / samples;
    File f = SD.open("/noise.csv", FILE_APPEND);
    if (f) { f.printf("%lu,%d,%d\n", millis() / 60000, avg, peak); f.close(); }
    Serial.printf("avg %d peak %d\n", avg, peak);
    total = 0; samples = 0; peak = 0; minuteStart = millis();
  }
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Quiet roomAverage below about 100
Talk near itAverage and peak rise in the next minute's line
Remove the card"SD card not found" at start-up, no crash

If it does not work

Constant 4095 peaks

Gain too high, or the mic is on 5 V: use 3V3.

Empty file

Card not FAT32, or wrong CS pin.

Readings never change

OUT not on GPIO34, or the module needs its gain turned up.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the noise trend logger?

ESP32 DevKit V1, MAX4466 microphone module, MicroSD Card Module and Breadboard 830 Tie Points.

How long does the noise trend logger take to build?

About 55 minutes for a intermediate maker, in 4 steps.

How do I know the noise trend logger works?

Quiet room: Average below about 100. Talk near it: Average and peak rise in the next minute's line. Remove the card: "SD card not found" at start-up, no crash.

Constant 4095 peaks: what should I check?

Gain too high, or the mic is on 5 V: use 3V3.

Empty file: what should I check?

Card not FAT32, or wrong CS pin.

Readings never change: what should I check?

OUT not on GPIO34, or the module needs its gain turned up.