Projects / Four-digit clock with TM1637

Four-digit clock with TM1637

Beginner2 hGuided buildReviewed

Build it step by step

0 of 8 done
  1. NANO

    Wire the display

    CLK to D5, DIO to D6, power to 5V and GND.

  2. NANO

    Wire the clock chip

    SDA to A4, SCL to A5, power to 5V and GND.

  3. NANO

    Wire the buttons

    D2 and D3 each to GND.

  4. NANO

    Upload the sketch

    The display shows roughly the compile time.

  5. NANO

    Press the hours button

    The hour advances.

  6. NANO

    Press the minutes button

    The minute advances.

  7. NANO

    Hold both buttons for a second

    The clock switches between 12 and 24 hours.

  8. NANO

    Unplug and replug the power

    The time is kept.

In short

How do you build a four-digit clock with TM1637?

A four-digit clock with a blinking colon, set with two buttons and kept accurate by an RTC. You need Arduino Nano, TM1637 4-digit display, DS3231 RTC module, Tactile push button 6 mm × 2, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 8 steps and about 120 minutes.

Level
Beginner
Time
About 120 min
Parts
6

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
TM1637 CLKNano D5Display clock
TM1637 DIONano D6Display data
TM1637 VCC and GNDNano 5V and GNDPower
RTC SDANano A4I2C data
RTC SCLNano A5I2C clock
RTC VCC and GNDNano 5V and GNDPower
Hours buttonNano D2 to GNDAdd one hour
Minutes buttonNano D3 to GNDAdd one minute

Code

A DS3231 real-time clock chip keeps accurate time, to within a minute or so a year, and carries on from a small backup cell when the board is switched off. The sketch reads the time over I2C and shows hours and minutes on the four-digit display, with the colon blinking every second by turning one segment bit on and off. The hours button adds an hour and the minutes button adds a minute, and both buttons held together switch between 24 hour and 12 hour mode. If the clock has never been set or lost power, the sketch sets it from the time it was compiled, which is usually a few seconds off, so use the buttons to correct it. Setting the minutes also resets the seconds to zero, which makes it easy to set the clock exactly against a reference. The display brightness is low by default; raise it with setBrightness for a bright room. A clean housing with a red filter makes a handsome bedside clock.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

#include <TM1637Display.h>
#include <RTClib.h>

const int CLK = 5, DIO = 6;
const int HOUR_BTN = 2, MIN_BTN = 3;
TM1637Display display(CLK, DIO);
RTC_DS3231 rtc;

bool mode24 = true;
bool lastColon = false;

void showTime(const DateTime& t, bool colon) {
  int h = t.hour();
  if (!mode24) { h = h % 12; if (h == 0) h = 12; }
  int value = h * 100 + t.minute();
  display.showNumberDecEx(value, colon ? 0b01000000 : 0, mode24);   // leading zero only in 24 hour mode
}

void setup() {
  pinMode(HOUR_BTN, INPUT_PULLUP);
  pinMode(MIN_BTN, INPUT_PULLUP);
  display.setBrightness(4);
  if (!rtc.begin()) { display.showNumberDec(8888); while (true) {} }
  if (rtc.lostPower()) rtc.adjust(DateTime(F(__DATE__), F(__TIME__)));   // start from the compile time
}

void loop() {
  DateTime now = rtc.now();
  bool hb = (digitalRead(HOUR_BTN) == LOW);
  bool mb = (digitalRead(MIN_BTN) == LOW);

  if (hb && mb) {                                      // both held: switch 12 and 24 hour mode
    delay(800);
    if (digitalRead(HOUR_BTN) == LOW && digitalRead(MIN_BTN) == LOW) mode24 = !mode24;
    while (digitalRead(HOUR_BTN) == LOW || digitalRead(MIN_BTN) == LOW) {}
  } else if (hb) {
    rtc.adjust(DateTime(now.year(), now.month(), now.day(), (now.hour() + 1) % 24, now.minute(), 0));
    delay(250);
  } else if (mb) {
    rtc.adjust(DateTime(now.year(), now.month(), now.day(), now.hour(), (now.minute() + 1) % 60, 0));
    delay(250);
  }

  bool colon = (now.second() % 2 == 0);                 // blink once a second
  showTime(rtc.now(), colon);
  delay(100);
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Power onTime shown with a blinking colon
Hours pressedHour up by one
Minutes pressedMinute up by one
Both held12 or 24 hour mode
Power off for a minuteTime still correct

If it does not work

Display shows 8888

The clock chip is not found, check the I2C wires.

Time resets each power cycle

Fit the backup cell in the clock module.

Colon does not blink

Check showNumberDecEx colon mask for your display.

Time a few seconds off

Set the minutes to reset the seconds.

Display too dim

Raise the value in setBrightness.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the four-digit clock with TM1637?

Arduino Nano, TM1637 4-digit display, DS3231 RTC module, Tactile push button 6 mm × 2, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm).

How long does the four-digit clock with TM1637 take to build?

About 120 minutes for a beginner maker, in 8 steps.

How do I know the four-digit clock with TM1637 works?

Power on: Time shown with a blinking colon. Hours pressed: Hour up by one. Minutes pressed: Minute up by one.

Display shows 8888: what should I check?

The clock chip is not found, check the I2C wires.

Time resets each power cycle: what should I check?

Fit the backup cell in the clock module.

Colon does not blink: what should I check?

Check showNumberDecEx colon mask for your display.

Time a few seconds off: what should I check?

Set the minutes to reset the seconds.