Projects / Negative supply from a single rail

Negative supply from a single rail

Beginner30 minGuided buildReviewed

Build it step by step

0 of 7 done
  1. ICL76604.18 V

    Place the chip

    Put the ICL7660 across the breadboard centre with pin 1 at the dot.

  2. Wire the pump

    Add the first capacitor between pins 2 and 4 with its + leg on pin 2.

  3. Add the reservoir

    Add the second capacitor from pin 5 to ground with its + leg on ground.

  4. USB

    Power up

    Connect 5 V from the USB breakout.

  5. Measure no load

    Read pin 5 against ground, which should be about -4.8 V.

  6. ICL76604.19 V

    Add loads

    Connect 1 kΩ, then 470 Ω, and watch the voltage fall.

  7. Use it

    Power a spare op-amp from +5 V and -5 V to see a symmetrical supply.

In short

How do you build a negative supply from a single rail?

An ICL7660 makes about -5 V from +5 V so op-amps get a split supply from USB. You need ICL7660 voltage inverter, Electrolytic capacitor 10 µF × 2, Resistor 1 kΩ, Digital multimeter, Breadboard 830 Tie Points, Jumper wires male to male (40 pcs, 20 cm) and USB-A female breakout. It takes 7 steps and about 30 minutes.

Level
Beginner
Time
About 30 min
Parts
7

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
USB breakout + (5 V)ICL7660 pin 8 (V+)Supply
USB breakout -ICL7660 pin 3 (GND)Ground
10 µF capacitorBetween pin 2 (CAP+) with + on pin 2 and pin 4 (CAP-)Pump capacitor
10 µF capacitorBetween pin 5 (VOUT) and GND, + on GND and - on pin 5Output reservoir
ICL7660 pins 6 and 7Left openNormal speed (LV pin open above 3.5 V)
1 kΩ resistorPin 5 and GNDTest load

No code needed

No code. The negative capacitor polarity matters: the output capacitor's positive leg goes to ground and its negative leg to pin 5. Output current is limited to about 20 mA and the voltage drops as you load it, so use it for op-amps, not motors. Pin 1 is next to the dot on the chip and pin 8 is opposite pin 1.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
No loadAbout -4.5 V to -5 V
1 kΩ load (about 5 mA)A little lower, about -4.3 V
Short load of 220 ΩNoticeably lower, showing the weak current limit
USB unpluggedOutput falls to 0 V

If it does not work

Output near 0 V

Check pin 3 is on ground and pin 8 on 5 V, and chip orientation.

Positive voltage out

Reservoir capacitor is the wrong way round. Swap it.

Chip gets hot

Output is overloaded or a capacitor is reversed. Disconnect and check.

Output very noisy

Add a 100 nF capacitor across the supply pins.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the negative supply from a single rail?

ICL7660 voltage inverter, Electrolytic capacitor 10 µF × 2, Resistor 1 kΩ, Digital multimeter, Breadboard 830 Tie Points, Jumper wires male to male (40 pcs, 20 cm) and USB-A female breakout.

How long does the negative supply from a single rail take to build?

About 30 minutes for a beginner maker, in 7 steps.

How do I know the negative supply from a single rail works?

No load: About -4.5 V to -5 V. 1 kΩ load (about 5 mA): A little lower, about -4.3 V. Short load of 220 Ω: Noticeably lower, showing the weak current limit.

Output near 0 V: what should I check?

Check pin 3 is on ground and pin 8 on 5 V, and chip orientation.

Positive voltage out: what should I check?

Reservoir capacitor is the wrong way round. Swap it.

Chip gets hot: what should I check?

Output is overloaded or a capacitor is reversed. Disconnect and check.

Output very noisy: what should I check?

Add a 100 nF capacitor across the supply pins.