Projects / Door opening counter

Door opening counter

A reed switch counts how many times a fridge or wardrobe door is opened and shows the total on a small display.

Beginner1.5 hGuided buildReviewed

Build it step by step

0 of 8 done
  1. NANO19.9 mASSD1306

    Install the libraries

    Adafruit SSD1306 and Adafruit GFX Library.

  2. NANO

    Wire the reed switch

    One side to D2, the other to GND.

  3. NANO19.9 mASSD1306

    Wire the button and OLED

    Button D3 to GND, OLED on A4 and A5.

  4. NANO

    Upload the sketch

    Display shows 0 openings.

  5. NANO

    Hold the magnet next to the switch

    Count stays at 0, door shut.

  6. NANO

    Move the magnet away and back

    Count rises to 1.

  7. NANO

    Open and close five times

    Count shows 5.

  8. NANO

    Hold the button two seconds

    Count returns to 0.

In short

How do you build a door opening counter?

A reed switch counts how many times a fridge or wardrobe door is opened and shows the total on a small display. You need Arduino Nano, Door reed switch MC-38, SSD1306 OLED Display, Tactile push button 6 mm, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 8 steps and about 90 minutes.

Level
Beginner
Time
About 90 min
Parts
6

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Reed switch one terminalNano D2Internal pull-up
Reed switch other terminalNano GNDClosed when the magnet is near
MagnetFixed on the door edgeNext to the reed switch when the door is shut
Reset buttonNano D3 to GNDHold two seconds to reset the count
OLED SDA and SCLNano A4 and A5I2C, address 0x3C
OLED VCC and GNDNano 5V and GNDCheck your module voltage

Code

The reed switch closes when the magnet is next to it, so a shut door reads LOW and an open door reads HIGH. The sketch counts one opening each time the state changes from closed to open, after a 150 millisecond debounce to ignore a door that wobbles. The count is held in RAM and written to EEPROM at most once per hour when it has changed, because EEPROM cells wear out after roughly 100,000 writes: once an hour is about 24 writes a day, which would take over ten years to wear out a cell. A power cut can lose up to an hour of counts, which is a good trade for a household counter. A blank EEPROM reads as all ones, so the sketch treats that value as zero on the first run. Hold the button for two seconds to reset the total. To count per day, add a real-time clock and reset at midnight. Install Adafruit SSD1306 and Adafruit GFX from the Library Manager.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

#include <Wire.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
#include <EEPROM.h>

Adafruit_SSD1306 oled(128, 64, &Wire, -1);

const uint8_t REED = 2, BTN = 3;
const unsigned long SAVE_EVERY_MS = 3600000UL;   // save at most once an hour to protect the EEPROM

uint32_t count = 0;
uint32_t savedCount = 0;
unsigned long lastSave = 0;
unsigned long lastOpenAt = 0;
bool doorOpen = false;
unsigned long changedAt = 0;
unsigned long btnDownAt = 0;

void saveCount() {
  EEPROM.put(0, count);
  savedCount = count;
  lastSave = millis();
}

void draw() {
  oled.clearDisplay();
  oled.setTextSize(1);
  oled.setCursor(0, 0);  oled.print("Door openings");
  oled.setTextSize(3);
  oled.setCursor(0, 16); oled.print(count);
  oled.setTextSize(1);
  oled.setCursor(0, 50);
  if (lastOpenAt == 0) oled.print("None since power on");
  else { oled.print("Last: "); oled.print((millis() - lastOpenAt) / 60000UL); oled.print(" min ago"); }
  if (doorOpen) { oled.setCursor(100, 0); oled.print("OPEN"); }
  oled.display();
}

void setup() {
  pinMode(REED, INPUT_PULLUP);
  pinMode(BTN, INPUT_PULLUP);
  oled.begin(SSD1306_SWITCHCAPVCC, 0x3C);
  oled.setTextColor(SSD1306_WHITE);
  EEPROM.get(0, count);
  if (count == 0xFFFFFFFF) count = 0;               // blank EEPROM reads as all ones
  savedCount = count;
  draw();
}

void loop() {
  bool open = (digitalRead(REED) == HIGH);          // magnet away from the switch means the door is open
  if (open != doorOpen && millis() - changedAt > 150) {   // 150 ms debounce
    changedAt = millis();
    doorOpen = open;
    if (open) { count++; lastOpenAt = millis(); }
    draw();
  }

  if (digitalRead(BTN) == LOW) {
    if (btnDownAt == 0) btnDownAt = millis();
    if (millis() - btnDownAt > 2000) { count = 0; saveCount(); btnDownAt = 0; draw(); delay(500); }
  } else {
    btnDownAt = 0;
  }

  if (count != savedCount && millis() - lastSave > SAVE_EVERY_MS) saveCount();

  static unsigned long lastDraw = 0;
  if (millis() - lastDraw > 30000) { lastDraw = millis(); draw(); }   // refresh the minutes
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Magnet next to the switchDoor shut, count unchanged
Magnet awayCount rises by one and OPEN shows
Wobble the doorOnly one count
Hold the button for two secondsCount resets
Power cycle after an hourThe saved count returns

If it does not work

Counts twice per opening

Increase the 150 ms debounce or fix the magnet more firmly.

Never counts

Check the reed wiring and the gap, reed switches work within about 1 cm.

Count lost after power cut

It saves hourly, lower SAVE_EVERY_MS for testing only.

Display blank

Try address 0x3D, and check the display voltage.

Reed switch glass broken

Mount it with tape and do not bend its leads near the glass.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the door opening counter?

Arduino Nano, Door reed switch MC-38, SSD1306 OLED Display, Tactile push button 6 mm, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm).

How long does the door opening counter take to build?

About 90 minutes for a beginner maker, in 8 steps.

How do I know the door opening counter works?

Magnet next to the switch: Door shut, count unchanged. Magnet away: Count rises by one and OPEN shows. Wobble the door: Only one count.

Counts twice per opening: what should I check?

Increase the 150 ms debounce or fix the magnet more firmly.

Never counts: what should I check?

Check the reed wiring and the gap, reed switches work within about 1 cm.

Count lost after power cut: what should I check?

It saves hourly, lower SAVE_EVERY_MS for testing only.

Display blank: what should I check?

Try address 0x3D, and check the display voltage.