Projects / M5Stack Core2 IoT panel

M5Stack Core2 IoT panel

Beginner1.5 hGuided buildReviewed
M5STACKGROVE

Build it step by step

0 of 7 done
  1. M5STACK

    Install the board package

    M5Stack in Boards Manager.

  2. M5STACK

    Install the libraries

    M5Unified and PubSubClient.

  3. M5STACK

    Draw the screen

    Test with the display only.

  4. M5STACK

    Add the touch button

    Check it responds.

  5. M5STACK

    Fill in Wi-Fi and MQTT

    Your own values.

  6. M5STACK

    Watch the topic

    With an MQTT client.

  7. M5STACKGROVE

    Add a Grove sensor

    If you like.

In short

How do you build an M5Stack Core2 IoT panel?

A ready-made touch device shows sensor values and switches things on, with no wiring. You need M5Stack Core2 and Grove cable 4-pin. It takes 7 steps and about 90 minutes.

Level
Beginner
Time
About 90 min
Parts
2

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Core2 USB-CComputer or chargerProgramming and power
Grove cableCore2 Port A (I2C) to an optional Grove sensorAdd a sensor later
Core2Built-in screen, touch, accelerometer and batteryNothing to wire

Code

The Core2 has the screen, touch panel, accelerometer, speaker, battery and Wi-Fi in one case, so this is a quick way to learn how a touch interface and MQTT fit together without any wiring. The sketch draws the battery level and tilt, and a big touch button that sends ON or OFF to the MQTT topic home/panel/light, which a Home Assistant or Node-RED flow can use to switch a lamp. Fill in the placeholder values for Wi-Fi and your broker, and do not post them anywhere public. The plain MQTT here is for a home network you control, not the internet. To add a sensor, plug a Grove I2C unit into Port A and read it with its own library, then show the value on the screen. The built-in battery is a small LiPo, so charge it with the supplied USB-C cable, keep it away from heat, and stop using the device if the case swells. Install the M5Stack boards package, choose M5Core2, and use M5Unified for the display and touch.

Runs on a virtual ESP32 Dev Module in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// M5Stack Core2 panel: shows battery and tilt, and a touch button that publishes ON or OFF to MQTT.
// Libraries: M5Unified, PubSubClient. Board: M5Stack Core2 (M5Stack boards package). Fill in the placeholders.
#include <M5Unified.h>
#include <WiFi.h>
#include <PubSubClient.h>
const char* WIFI_SSID = "YOUR_WIFI_NAME";
const char* WIFI_PASS = "YOUR_WIFI_PASSWORD";
const char* MQTT_HOST = "YOUR_BROKER_ADDRESS";
const char* MQTT_USER = "YOUR_MQTT_USER";
const char* MQTT_PASS = "YOUR_MQTT_PASSWORD";
WiFiClient net;
PubSubClient mqtt(net);
bool lightOn = false;
unsigned long lastDraw = 0;
void draw() {
  M5.Display.fillScreen(BLACK);
  M5.Display.setTextColor(WHITE);
  M5.Display.setTextSize(2);
  M5.Display.setCursor(10, 10);
  M5.Display.printf("Battery %d%%", M5.Power.getBatteryLevel());
  float ax, ay, az;
  M5.Imu.getAccel(&ax, &ay, &az);
  M5.Display.setCursor(10, 40);
  M5.Display.printf("Tilt x %.2f y %.2f", ax, ay);
  M5.Display.fillRoundRect(60, 100, 200, 90, 12, lightOn ? GREEN : DARKGREY);
  M5.Display.setTextColor(BLACK);
  M5.Display.setCursor(110, 135);
  M5.Display.print(lightOn ? "LIGHT ON" : "LIGHT OFF");
}
void setup() {
  auto cfg = M5.config();
  M5.begin(cfg);
  WiFi.begin(WIFI_SSID, WIFI_PASS);
  mqtt.setServer(MQTT_HOST, 1883);
  draw();
}
void loop() {
  M5.update();
  if (WiFi.status() == WL_CONNECTED && !mqtt.connected()) mqtt.connect("core2-panel", MQTT_USER, MQTT_PASS);
  mqtt.loop();
  auto t = M5.Touch.getDetail();
  if (t.wasPressed() && t.x > 60 && t.x < 260 && t.y > 100 && t.y < 190) {
    lightOn = !lightOn;
    if (mqtt.connected()) mqtt.publish("home/panel/light", lightOn ? "ON" : "OFF");
    draw();
  }
  if (millis() - lastDraw > 2000) { lastDraw = millis(); draw(); }
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Power onBattery and tilt shown
Tilt the deviceNumbers change
Touch the buttonColour changes and MQTT message sent
Two seconds laterScreen refreshes

If it does not work

Touch does not respond

Use M5Unified and check the button area.

No MQTT message

Check Wi-Fi, broker address and credentials.

Wrong board error

Select M5Core2.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the M5Stack Core2 IoT panel?

M5Stack Core2 and Grove cable 4-pin.

How long does the M5Stack Core2 IoT panel take to build?

About 90 minutes for a beginner maker, in 7 steps.

How do I know the M5Stack Core2 IoT panel works?

Power on: Battery and tilt shown. Tilt the device: Numbers change. Touch the button: Colour changes and MQTT message sent.

Touch does not respond: what should I check?

Use M5Unified and check the button area.

No MQTT message: what should I check?

Check Wi-Fi, broker address and credentials.

Wrong board error: what should I check?

Select M5Core2.