Projects / Logic probe with three LEDs

Logic probe with three LEDs

A probe shows high, low or floating states of a digital pin using three LEDs.

Beginner2 hGuided buildReviewed

Build it step by step

0 of 8 done
  1. NANO

    Wire the divider

    Two 10 kilohm resistors to A0, one to 5V, one to GND.

  2. NANO14.5 mA

    Wire the three LEDs

    Red D4, green D5, yellow D6, each with 220 ohm.

  3. NANO

    Add the probe wire and ground clip

    Probe on A0, ground clip on GND.

  4. NANO14.5 mA

    Upload the sketch

    With the probe in the air, yellow is on.

  5. NANO

    Touch the probe to 5V

    Green lights.

  6. NANO

    Touch it to GND

    Red lights.

  7. NANO14.6 mA

    Probe the LED pin of another board running Blink

    Red and green blink together as a pulse.

  8. NANO

    Probe a 3.3 V pin

    Green lights.

In short

How do you build a logic probe with three LEDs?

A probe shows high, low or floating states of a digital pin using three LEDs. You need Arduino Nano, LED 5 mm red, LED 5 mm green, LED 5 mm yellow, Resistor 220 Ω × 3, Resistor 10 kΩ × 2, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 8 steps and about 120 minutes.

Level
Beginner
Time
About 120 min
Parts
8

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Probe tip wireNano A0Touch this to the pin you are testing
10 kilohm from 5V to A0Nano A0Pulls a floating pin up to the middle
10 kilohm from A0 to GNDNano A0Together they hold an open probe near 2.5 V
Red LED plus through 220 ohmNano D4Low
Green LED plus through 220 ohmNano D5High
Yellow LED plus through 220 ohmNano D6Floating or in between
LED minus legsNano GNDCommon ground
Probe ground clipNano GNDJoin to the circuit under test

Code

A digital pin is normally either high or low, but an unconnected pin is neither: it floats and picks up noise. Two equal 10 kilohm resistors hold an open probe at about 2.5 V, which falls between the low and high limits, so the yellow LED shows floating, a broken wire or a tri-stated output. A driven output is much stiffer than the 5 kilohm divider, so it overrides it and the reading goes high or low as expected. The sketch uses 0.8 V and 2.9 V as the limits so it works for 5 V logic and for 3.3 V logic, where a high is about 3.3 V. The Nano reads the pin as fast as it can for 60 milliseconds, and if it sees both high and low in that window it shows red and green together to tell you the signal is pulsing, such as a PWM or clock line. This probe is for 5 V and 3.3 V logic only. Never touch it to mains, a motor supply or anything above 5 V.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

const uint8_t PIN_PROBE = A0;
const uint8_t LED_LOW = 4;      // red
const uint8_t LED_HIGH = 5;     // green
const uint8_t LED_MID = 6;      // yellow

// Thresholds in ADC counts (5 V reference, 1023 counts).
const int LOW_MAX = 164;        // below about 0.8 V counts as low
const int HIGH_MIN = 594;       // above about 2.9 V counts as high (works for 3.3 V and 5 V logic)

void setup() {
  pinMode(LED_LOW, OUTPUT);
  pinMode(LED_HIGH, OUTPUT);
  pinMode(LED_MID, OUTPUT);
}

void loop() {
  bool sawLow = false, sawHigh = false;
  unsigned long t0 = millis();
  while (millis() - t0 < 60) {            // watch for 60 ms, long enough to catch slow pulses
    int v = analogRead(PIN_PROBE);        // about 110 microseconds per reading
    if (v <= LOW_MAX) sawLow = true;
    else if (v >= HIGH_MIN) sawHigh = true;
  }
  int last = analogRead(PIN_PROBE);

  if (sawLow && sawHigh) {                // a pulse train: show both red and green
    digitalWrite(LED_LOW, HIGH);
    digitalWrite(LED_HIGH, HIGH);
    digitalWrite(LED_MID, LOW);
  } else if (last <= LOW_MAX) {
    digitalWrite(LED_LOW, HIGH);  digitalWrite(LED_HIGH, LOW);  digitalWrite(LED_MID, LOW);
  } else if (last >= HIGH_MIN) {
    digitalWrite(LED_LOW, LOW);   digitalWrite(LED_HIGH, HIGH); digitalWrite(LED_MID, LOW);
  } else {
    digitalWrite(LED_LOW, LOW);   digitalWrite(LED_HIGH, LOW);  digitalWrite(LED_MID, HIGH);
  }
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Probe open in the airYellow on
Probe on 5VGreen only
Probe on GNDRed only
Probe on a 3.3 V logic highGreen only
Probe on a fast PWM pinRed and green on together

If it does not work

Always yellow

The probe is not reaching a driven pin, or the ground clip is not joined.

Red and green flicker when touching 5V

Check for a loose probe connection.

Open probe shows green or red

One divider resistor is the wrong value or missing.

3.3 V high shows yellow

Check the supply is really 3.3 V and lower HIGH_MIN a little.

Slow pulses seem steady

Increase the 60 ms watch window to catch slower signals.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the logic probe with three LEDs?

Arduino Nano, LED 5 mm red, LED 5 mm green, LED 5 mm yellow, Resistor 220 Ω × 3, Resistor 10 kΩ × 2, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm).

How long does the logic probe with three LEDs take to build?

About 120 minutes for a beginner maker, in 8 steps.

How do I know the logic probe with three LEDs works?

Probe open in the air: Yellow on. Probe on 5V: Green only. Probe on GND: Red only.

Always yellow: what should I check?

The probe is not reaching a driven pin, or the ground clip is not joined.

Red and green flicker when touching 5V: what should I check?

Check for a loose probe connection.

Open probe shows green or red: what should I check?

One divider resistor is the wrong value or missing.

3.3 V high shows yellow: what should I check?

Check the supply is really 3.3 V and lower HIGH_MIN a little.