Projects / LM386 mini speaker amplifier

LM386 mini speaker amplifier

Beginner1.5 hGuided buildReviewed

Build it step by step

0 of 6 done
  1. Plan the layout

    Draw the pin numbers first. Pin 1 and 8 are the gain pins, 2 and 3 the inputs, 4 ground, 5 output, 6 supply, 7 bypass.

  2. Power and decoupling

    9 V to pin 6 and ground to pin 4. Add 100 µF across the supply close to the chip.

  3. AUDIO+

    Wire the input

    Jack tip through 10 µF to the pot's top, pot bottom to ground, wiper to pin 3. Tie pin 2 to ground.

  4. Wire the output

    Pin 5 through the 220 µF (positive to pin 5) to the speaker, other speaker wire to ground. Add the 10 Ω and 47 nF from pin 5 to ground.

  5. Add the bypass

    10 µF from pin 7 to ground.

  6. Listen

    Play music from a phone at low volume, then raise it. Try the 10 µF between pins 1 and 8 and compare the loudness.

In short

How do you build an LM386 mini speaker amplifier?

A single LM386 chip drives a small speaker from a phone's headphone output, with a volume pot and gain of 20 or 200. You need LM386 audio amplifier IC, Potentiometer 10 kΩ, Electrolytic capacitor 220 µF, Electrolytic capacitor 10 µF × 3, Electrolytic Capacitor 100 µF, Ceramic capacitor 47 nF, Resistor 10 Ω, Speaker 8 Ω 0.5 W, Audio jack 3.5 mm (PCB, stereo), 9 V battery, 9 V battery snap with DC jack and Perfboard (dot PCB) 7 × 9 cm. It takes 6 steps and about 90 minutes.

Level
Beginner
Time
About 90 min
Parts
12

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
9 V battery +LM386 pin 6 (VS), with 100 µF to GNDSupply and decoupling
9 V battery -LM386 pin 4 (GND)Ground
Audio jack tip (left)10 µF (+ to jack) then top of the potSignal in
Audio jack sleeveBottom of the pot and groundSignal ground
Pot wiperLM386 pin 3 (IN+)Volume control
LM386 pin 2 (IN-)GroundUnused input
10 µF (+ on pin 1)Between pin 1 and pin 8Raises gain from 20 to 200 (leave out for 20)
LM386 pin 710 µF to groundBypass for hum rejection
LM386 pin 5 (OUT)220 µF (+ to pin 5), then speaker +Output coupling capacitor
Speaker -GroundReturn
10 Ω in series with 47 nFPin 5 to groundZobel network, stops high-frequency oscillation

No code needed

No code. Gain is 20 with pins 1 and 8 open and 200 with 10 µF between them. A 9 V battery is fine for listening tests, but a small speaker at full gain can distort, so keep the volume low. Use only the tip (left channel) of the stereo jack.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
No input, pot at maximumA quiet hiss only, no loud hum
Music at gain 20Clean but quiet
Music at gain 200Much louder, with more hiss
Speaker bodyCool, the chip only warms slightly

If it does not work

Loud squeal or motorboating

The Zobel network or supply decoupling is missing, or the input wires are too long. Add the parts and shorten the wires.

Very quiet

The phone volume is low or the jack tip is not connected. Check it with the volume up.

Hum

Add the pin 7 bypass capacitor and keep input wires away from the supply.

Distortion on loud notes

A 9 V battery sags with a 0.5 W speaker. Lower the volume or use gain 20.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the LM386 mini speaker amplifier?

LM386 audio amplifier IC, Potentiometer 10 kΩ, Electrolytic capacitor 220 µF, Electrolytic capacitor 10 µF × 3, Electrolytic Capacitor 100 µF, Ceramic capacitor 47 nF, Resistor 10 Ω, Speaker 8 Ω 0.5 W, Audio jack 3.5 mm (PCB, stereo), 9 V battery, 9 V battery snap with DC jack and Perfboard (dot PCB) 7 × 9 cm.

How long does the LM386 mini speaker amplifier take to build?

About 90 minutes for a beginner maker, in 6 steps.

How do I know the LM386 mini speaker amplifier works?

No input, pot at maximum: A quiet hiss only, no loud hum. Music at gain 20: Clean but quiet. Music at gain 200: Much louder, with more hiss.

Loud squeal or motorboating: what should I check?

The Zobel network or supply decoupling is missing, or the input wires are too long. Add the parts and shorten the wires.

Very quiet: what should I check?

The phone volume is low or the jack tip is not connected. Check it with the volume up.

Hum: what should I check?

Add the pin 7 bypass capacitor and keep input wires away from the supply.

Distortion on loud notes: what should I check?

A 9 V battery sags with a 0.5 W speaker. Lower the volume or use gain 20.