Projects / Lighthouse beam at dusk

Lighthouse beam at dusk

Beginner2 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. PICO19.1 mA

    Wire the ring

    5V to VBUS, GND to GND, DIN through 330 ohms to GP15.

  2. PICO862 lux

    Build the divider

    LDR from 3V3(OUT) to GP26, 10 kilo-ohms from GP26 to GND.

  3. PICO19.1 mA

    Run the program

    In a bright room the ring is dark.

  4. PICO864 lux

    Cover the LDR with your hand

    The beam fades in and sweeps round.

  5. PICO

    Uncover it

    The beam fades away.

  6. PICO

    Tune the numbers

    Change DARK_BELOW and LIGHT_ABOVE to suit your room.

  7. PICO

    Save as main.py

    So it starts on power-up.

In short

How do you build a lighthouse beam at dusk?

A Pico sweeps a bright beam round a 16-LED ring like a lighthouse, but only after a photoresistor sees that the room has gone dark, and fades away at dawn. You need Raspberry Pi Pico H, WS2812B ring 16 LEDs, LDR Photoresistor, Resistor 10 kΩ, Resistor 330 Ω and Breadboard 830 Tie Points. It takes 7 steps and about 120 minutes.

Level
Beginner
Time
About 120 min
Parts
6

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Ring 5VPico VBUS pin 405 V from USB (brightness is kept low)
Ring GNDPico GND pin 38Common ground
Ring DIN330 ohm resistor to Pico GP15 pin 20Data line
Photoresistor leg 1Pico 3V3(OUT) pin 36Top of the divider
Photoresistor leg 2Pico GP26 pin 31 and the 10 kilo-ohm resistorDivider output
10 kilo-ohm resistor other endPico GND pin 33Bottom of the divider

Code

A photoresistor, or LDR, is a resistor whose resistance falls when light falls on it. With a 10 kilo-ohm resistor it forms a voltage divider, and the voltage at the middle goes up in bright light and down in the dark, which the Pico reads with its analog input. The program averages eight readings and decides it is dark below one number and light again above a higher number. Using two numbers, called hysteresis, stops it flickering at dusk. When it is dark the beam fades in over a few seconds, and when it is light it fades out. The beam is drawn as one bright LED with a dimmer tail behind it, moving one step at a time round the ring, like a lighthouse lamp. The WS2812B ring has a control chip in each LED, and the 330 ohm resistor protects the first one on the data line. The brightness is held to twenty percent, which keeps the current well within what a USB port can give and is gentler on the eyes. Do not look into the ring at close range. Point the photoresistor away from the ring so the beam does not turn it off.

from machine import Pin, ADC
import neopixel
import time

N = 16
ring = neopixel.NeoPixel(Pin(15), N)
ldr = ADC(26)

DARK_BELOW = 18000                                  # the reading goes down as the room gets dark
LIGHT_ABOVE = 24000                                 # a higher number for waking again (avoids flicker)
MAX_BRIGHT = 0.2                                    # keep the ring dim: 20 percent

dark = False
level = 0.0
pos = 0

def scaled(rgb, k):
    return (int(rgb[0] * k), int(rgb[1] * k), int(rgb[2] * k))

while True:
    total = 0
    for _ in range(8):
        total += ldr.read_u16()
    reading = total // 8
    if reading < DARK_BELOW:
        dark = True
    elif reading > LIGHT_ABOVE:
        dark = False

    target = 1.0 if dark else 0.0
    level += (target - level) * 0.05                # fade in and out over a few seconds

    for i in range(N):
        ring[i] = (0, 0, 0)
    beam = (255, 210, 120)
    ring[pos] = scaled(beam, level * MAX_BRIGHT)
    ring[(pos - 1) % N] = scaled(beam, level * MAX_BRIGHT * 0.35)
    ring[(pos - 2) % N] = scaled(beam, level * MAX_BRIGHT * 0.10)
    ring.write()

    if level > 0.02:
        pos = (pos + 1) % N                         # sweep only while the beam is on
    time.sleep_ms(90)

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Bright roomRing off
Cover the LDRBeam fades in over a few seconds
BeamOne bright LED with a tail sweeping round
Uncover the LDRFades out
Dim lightNo flicker between on and off

If it does not work

Ring never lights

Check the data arrow, 5 V and the order of the wires.

Always lit

Raise DARK_BELOW, or move the LDR out of the shade.

Never lights

Lower DARK_BELOW and LIGHT_ABOVE, or check the divider wiring.

Flickers

Widen the gap between the two numbers.

Wrong colour

The ring may use a different order, swap the colour values.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the lighthouse beam at dusk?

Raspberry Pi Pico H, WS2812B ring 16 LEDs, LDR Photoresistor, Resistor 10 kΩ, Resistor 330 Ω and Breadboard 830 Tie Points.

How long does the lighthouse beam at dusk take to build?

About 120 minutes for a beginner maker, in 7 steps.

How do I know the lighthouse beam at dusk works?

Bright room: Ring off. Cover the LDR: Beam fades in over a few seconds. Beam: One bright LED with a tail sweeping round.

Ring never lights: what should I check?

Check the data arrow, 5 V and the order of the wires.

Always lit: what should I check?

Raise DARK_BELOW, or move the LDR out of the shade.

Never lights: what should I check?

Lower DARK_BELOW and LIGHT_ABOVE, or check the divider wiring.

Flickers: what should I check?

Widen the gap between the two numbers.