Projects / LED bulb and tube driver tester

LED bulb and tube driver tester

Intermediate1 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. Unplug the bulb

    Wait a few minutes.

  2. Open it carefully

    Remove the LED board only.

  3. DPS5005

    Set the supply to 10 mA

    A few volts.

  4. CROCOD

    Clip across the first LED

    Check the polarity.

  5. Raise the voltage slowly

    Until it glows.

  6. Move along the string

    Find the one that stays dark.

  7. Decide to bridge or replace

    Short term only.

In short

How do you build an LED bulb and tube driver tester?

A safe tester for LED bulb boards that checks each LED string with a current-limited DC supply. You need Adjustable bench power supply module (DPS5005), Digital multimeter, Crocodile clip test leads (10 pack) and Resistor 1 kΩ. It takes 7 steps and about 60 minutes.

Level
Intermediate
Time
About 60 min
Parts
4

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
DPS5005 output plusRed crocodile leadTest supply plus
DPS5005 output minusBlack crocodile leadTest supply minus
Crocodile leadsAcross one LED or one LED string on the bulb board, with the board removed from the bulbThe part under test
1 k resistorIn series with the lead when testing a single LED by itselfExtra current limit
MultimeterIn series on the current range, or in diode test modeCheck LED forward voltage

No code needed

A dead LED bulb is often one failed LED in a string, and with the board out of the bulb you can find it safely on the bench with a low-voltage, current-limited supply. This is for the LED board only: never test with the bulb connected to mains, and never touch the driver side. The driver can hold a charge in its capacitors long after unplugging, and mains voltages can kill, so only take the board out when the bulb is unplugged for a few minutes, and if you are not sure how to open it, do not. Set the DPS5005 to a current limit of 10 mA, a voltage of a few volts, and clip across one LED, or one section where the board is divided, with the right polarity. Raise the voltage slowly: a working LED lights at about 3 V at that tiny current, while a dead one stays dark or the voltage runs up with nothing lit. A string of LEDs in series needs its voltage, about 3 V times the number of LEDs, up to the supply's 50 V limit, so test sections one at a time. A dead LED can often be bridged with a short length of wire for a temporary repair, but the bulb will then run its other LEDs a little harder, so use it for a short time only and do not leave it unattended. Wear glasses and do not look into an LED at close range. There is no code.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Good LEDLights faintly at about 3 V
Dead LEDStays dark, voltage climbs
Supply currentNever above the 10 mA limit
Bridged boardRemaining LEDs light

If it does not work

Nothing lights

Check the polarity and that the clips touch the pads.

Voltage rises to the limit

That section is open; test smaller parts.

Faint glow only

Normal at 10 mA; raise the limit to a little more if needed.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the LED bulb and tube driver tester?

Adjustable bench power supply module (DPS5005), Digital multimeter, Crocodile clip test leads (10 pack) and Resistor 1 kΩ.

How long does the LED bulb and tube driver tester take to build?

About 60 minutes for a intermediate maker, in 7 steps.

How do I know the LED bulb and tube driver tester works?

Good LED: Lights faintly at about 3 V. Dead LED: Stays dark, voltage climbs. Supply current: Never above the 10 mA limit.

Nothing lights: what should I check?

Check the polarity and that the clips touch the pads.

Voltage rises to the limit: what should I check?

That section is open; test smaller parts.

Faint glow only: what should I check?

Normal at 10 mA; raise the limit to a little more if needed.