Projects / Constant-current LED driver with LM317

Constant-current LED driver with LM317

Beginner1 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. Calculate the resistor

    1.25 V divided by the current.

  2. Join four 1 ohm resistors

    In series for 4 ohms.

  3. LM317

    Wire the LM317

    IN, OUT and ADJ.

  4. LM3174.98V

    Mount the LM317 on the heatsink

    Insulate the tab.

  5. 19.5 mA

    Mount the LED on a heatsink

    Thermal paste.

  6. Measure the current

    Meter in series.

  7. LM317

    Work out the heat

    Volts across the LM317 times current.

In short

How do you build a constant-current LED driver with LM317?

An LM317 with one resistor drives a 1 W LED at a steady 300 mA from a 12 V supply. You need LM317 adjustable regulator, Wirewound resistor 1 Ω 10 W × 4, High-power LED 1 W white (star), Heatsink TO-220 and 12 V 2 A DC adapter. It takes 7 steps and about 60 minutes.

Level
Beginner
Time
About 60 min
Parts
5

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
12 V adapter plusLM317 IN (right pin, front view)Supply
LM317 OUT (middle pin)Four 1 ohm resistors in series, then LM317 ADJ (left pin)Current-setting resistor
LM317 ADJ and resistor endLED star anode (plus)Load
LED star cathode (minus)12 V adapter minusReturn
HeatsinkLM317 metal tab (use an insulating pad if the tab touches anything)Cooling

No code needed

The LM317 is usually a voltage regulator, but if you put a resistor between its output and its adjust pin it holds 1.25 V across that resistor, and so the current through it is 1.25 V divided by the resistance. Four 1 ohm resistors in series make 4 ohms, so the current is about 310 mA, steady even when the supply voltage changes. That is exactly what an LED wants, since the brightness depends on current, not on voltage. The LED drops about 3.2 V and the resistor 1.25 V, so the LM317 itself drops the remaining 7 V or so at 0.31 A: that is about 2.4 W of heat, which is why it needs a heatsink and gets hot to the touch. A lower supply voltage wastes less: about 6.5 V is the least that works. The LED star also gets warm, so mount it on a heatsink as well. The LED is very bright, so do not look into it, and use the right polarity on the LED, because a reversed LED simply does not light. Use only a sealed 12 V adapter. There is no code for this build.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
LEDLights at steady brightness
CurrentAbout 0.3 A on the meter
Change the supply from 9 to 12 VCurrent stays the same
LM317 temperatureWarm to hot, not too hot to touch for a second

If it does not work

LED dim

Check the resistor total and the supply voltage.

LM317 too hot

Lower the supply voltage or add a bigger heatsink.

No light

Check the LED polarity and the pin order.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the constant-current LED driver with LM317?

LM317 adjustable regulator, Wirewound resistor 1 Ω 10 W × 4, High-power LED 1 W white (star), Heatsink TO-220 and 12 V 2 A DC adapter. Wirewound resistor 1 Ω 10 W × 4: Four in series make 4 Ω, about 310 mA.

How long does the constant-current LED driver with LM317 take to build?

About 60 minutes for a beginner maker, in 7 steps.

How do I know the constant-current LED driver with LM317 works?

LED: Lights at steady brightness. Current: About 0.3 A on the meter. Change the supply from 9 to 12 V: Current stays the same.

LED dim: what should I check?

Check the resistor total and the supply voltage.

LM317 too hot: what should I check?

Lower the supply voltage or add a bigger heatsink.

No light: what should I check?

Check the LED polarity and the pin order.