Projects / COB LED floodlight driver

COB LED floodlight driver

Intermediate2 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. 17.1 mA17.1 mA

    Mount the COB on the heatsink

    Paste and screws.

  2. 27.8°C

    Fix the thermistor

    Near the LED.

  3. XL401517.1 mA

    Set the buck voltage

    A little above the LED's rating.

  4. Set the current limit

    Meter in series, about 0.8 A.

  5. 4.98V

    Switch on briefly

    Check the heatsink warms.

  6. Run for 30 minutes

    Check the temperature.

  7. Fit it in a mount

    With air round it.

In short

How do you build a COB LED floodlight driver?

A 10 W COB LED runs from 12 V through a buck converter set to constant current, with a big heatsink. You need 10 W COB LED (12 V), XL4015 5 A buck converter module, Heatsink TO-220, Thermal paste, 12 V 2 A DC adapter and NTC thermistor 10 kΩ (B3950). It takes 7 steps and about 120 minutes.

Level
Intermediate
Time
About 120 min
Parts
6

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
12 V adapterXL4015 IN+ and IN-Power
XL4015 OUT+COB LED plusDriven at constant current
XL4015 OUT-COB LED minusReturn
COB LEDMounted on a large finned heatsink with thermal pasteCooling
NTC thermistorGlued to the heatsink, leads to a multimeterTemperature check (10 k at 25 C)

No code needed

A bright LED must be driven by current, not by a fixed voltage, because its voltage drops as it warms and the current would then climb until it fails. The XL4015 buck converter has a current limit trimmer: set the output voltage to the LED's rated voltage or higher, put the meter in series with the LED, and turn the current trimmer until the meter shows the rated current. A 10 W COB at 12 V takes about 0.8 A; stay at or below the rating. Most of the 10 W becomes heat, so the LED must be mounted on a large finned heatsink with thermal paste, and the heatsink will get warm to hot. Glue the thermistor to the heatsink and check its resistance with a meter: a drop to a few kilohms means it is getting very hot, so stop. Never look straight into the LED, which is very bright, and never run it without its heatsink, even for a short test. Use only a sealed 12 V adapter, and keep it away from anything that can melt or burn. There is no code for this build.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
CurrentSteady at the set value
BrightnessConstant over time
Heatsink after 30 minutesWarm to hot, not too hot to touch for a second
ThermistorResistance falls as it warms

If it does not work

LED flickers

Check the connections and the current limit setting.

Heatsink too hot

Use a larger heatsink or lower the current.

Dim

The current limit is set too low.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the COB LED floodlight driver?

10 W COB LED (12 V), XL4015 5 A buck converter module, Heatsink TO-220, Thermal paste, 12 V 2 A DC adapter and NTC thermistor 10 kΩ (B3950). Heatsink TO-220: Use a large finned heatsink.

How long does the COB LED floodlight driver take to build?

About 120 minutes for a intermediate maker, in 7 steps.

How do I know the COB LED floodlight driver works?

Current: Steady at the set value. Brightness: Constant over time. Heatsink after 30 minutes: Warm to hot, not too hot to touch for a second.

LED flickers: what should I check?

Check the connections and the current limit setting.

Heatsink too hot: what should I check?

Use a larger heatsink or lower the current.

Dim: what should I check?

The current limit is set too low.