Projects / LED bow tie

LED bow tie

Beginner1 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. DIGISPAR17.2 mA

    Test one LED

    Light it with the NeoPixel example.

  2. DIGISPAR

    Chain six

    Run a simple colour wipe.

  3. DIGISPAR17.2 mA

    Write the sparkle

    Fade a random LED in and out.

  4. DIGISPAR

    Write the rainbow

    Fade colours along the tie.

  5. DIGISPAR+

    Add the switch

    Put it in the battery lead.

  6. DIGISPAR+

    Fit the battery

    Insulated pouch in the knot.

  7. DIGISPAR17.3 mA

    Sew the tie

    Cover the LEDs with thin white fabric.

In short

How do you build an LED bow tie?

A bow tie with tiny addressable LEDs that sparkle, run on a coin cell or small Li-po. You need Digispark ATtiny85 USB board, WS2812B single LED module (8 mm / breakout) × 6, Li-Po battery 3.7 V 500 mAh and Slide switch SPDT (SS12D00). It takes 7 steps and about 60 minutes.

Level
Beginner
Time
About 60 min
Parts
4

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
LED module 1 DINDigispark P0Data
LED module DOUTNext module DINChain of six
LED modules VCC and GNDDigispark 5V pin and GNDPower (fed from the LiPo, see the notes)
LiPo plusSlide switch, then Digispark 5V pinPower switch
LiPo minusDigispark GNDGround

Code

The Digispark is a tiny ATtiny85 board that runs the NeoPixel library. Its on-board regulator wants a higher voltage, so with a 3.7 V LiPo you feed the cell straight to the 5V pin, which most people do; the LEDs and chip then run at 3.7 V and still work at low brightness. A coin cell cannot give the current LEDs need, so use a small LiPo and keep brightness at about 12 percent, which gives hours of light. Use a protected LiPo, put it in an insulated pouch hidden in the knot, never wear it while it charges, and take it off if it feels warm. The effects here are slow fades, avoiding fast flashing that can trigger people with photosensitive epilepsy. Install the Digispark board support from Digistump and upload by plugging the board in only when the IDE asks you to. The tie must sit comfortably and nothing sharp should press on the neck.

Runs on a virtual Digispark ATtiny85 in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// LED bow tie: sparkle and slow rainbow. Library: Adafruit NeoPixel. Board: Digispark (Default - 16.5 MHz).
#include <Adafruit_NeoPixel.h>
#define PIN 0
Adafruit_NeoPixel px(6, PIN, NEO_GRB + NEO_KHZ800);
unsigned long modeStart = 0;
int mode = 0;

void setup() {
  px.begin();
  px.setBrightness(30);                       // low brightness: easy on the battery and on the eyes
  randomSeed(analogRead(1));
}

void loop() {
  if (millis() - modeStart > 15000) { mode = (mode + 1) % 2; modeStart = millis(); }
  if (mode == 0) {                            // sparkle: a random LED twinkles softly
    px.clear();
    int i = random(6);
    for (int b = 0; b <= 255; b += 17) { px.setPixelColor(i, px.Color(b, b, b / 2)); px.show(); delay(8); }
    for (int b = 255; b >= 0; b -= 17) { px.setPixelColor(i, px.Color(b, b, b / 2)); px.show(); delay(8); }
    delay(random(100, 400));
  } else {                                    // slow rainbow across the tie
    static uint16_t hue = 0;
    for (int i = 0; i < 6; i++) px.setPixelColor(i, px.gamma32(px.ColorHSV(hue + i * 4000)));
    px.show(); hue += 200; delay(30);
  }
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Switch onSparkle starts
After 15 secondsSlow rainbow
BrightnessComfortable, no glare
Switch offAll dark, no glow

If it does not work

LEDs do not light

Check DIN goes to P0 and the polarity.

Random colours

Check the chain order and the NEO_GRB setting.

Upload fails

Plug the board in only when the IDE asks.

Dim or flickering

Charge the cell.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the LED bow tie?

Digispark ATtiny85 USB board, WS2812B single LED module (8 mm / breakout) × 6, Li-Po battery 3.7 V 500 mAh and Slide switch SPDT (SS12D00).

How long does the LED bow tie take to build?

About 60 minutes for a beginner maker, in 7 steps.

How do I know the LED bow tie works?

Switch on: Sparkle starts. After 15 seconds: Slow rainbow. Brightness: Comfortable, no glare.

LEDs do not light: what should I check?

Check DIN goes to P0 and the polarity.

Random colours: what should I check?

Check the chain order and the NEO_GRB setting.

Upload fails: what should I check?

Plug the board in only when the IDE asks.

Dim or flickering: what should I check?

Charge the cell.