Projects / LDR versus lux sensor comparison lab

LDR versus lux sensor comparison lab

Beginner1 hGuided buildReviewed

Build it step by step

0 of 6 done
  1. UNOBH1750358 lux

    Wire both sensors

    Build the LDR divider and connect the BH1750 on I2C.

  2. UNO

    Print both

    Open the Serial Monitor and see lux and ADC together.

  3. UNO

    Collect data

    Move a lamp in steps from far to near and note 15 or 20 pairs.

  4. UNO

    Plot

    Paste into a spreadsheet and draw lux against ADC.

  5. UNO

    Fit a power curve

    Add a trendline of the form lux = A × adc^B and note A and B.

  6. UNOBH1750362 lux

    Test the fit

    Put A and B in the sketch and compare the estimate with the BH1750.

In short

How do you build an LDR versus lux sensor comparison lab?

Measure the same light with a cheap LDR and a calibrated BH1750 lux sensor and plot why LDRs are non-linear. You need Arduino Uno R3, LDR Photoresistor, Resistor 10 kΩ, BH1750 light sensor, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 6 steps and about 60 minutes.

Level
Beginner
Time
About 60 min
Parts
6

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
5VLDR leg 1Top of the divider
LDR leg 2Uno A0 and 10 kΩ resistor to GNDAnalog reading
BH1750 VCC, GNDUno 5V, GNDPower
BH1750 SDA, SCLUno A4, A5I2C

Code

Arduino IDE, board "Arduino Uno". Install "BH1750" by Christopher Laws. Put the LDR and the BH1750 side by side facing the same lamp, and change only the lamp's distance. The CSV can be pasted into a spreadsheet: plot lux on one axis against ADC on the other, then add a power trendline. The LDR resistance falls with light in roughly a power-law, so a log-log plot of the divider reading looks nearly straight.

Runs on a virtual Arduino Uno in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

#include <Wire.h>
#include <BH1750.h>

BH1750 meter;
const byte LDR = A0;
// After you have fitted lux = A * adc^B in a spreadsheet, put your numbers here:
const float A = 0.0, B = 1.0;

void setup() {
  Serial.begin(9600);
  Wire.begin();
  meter.begin();
  Serial.println("lux,adc,estimate");
}

void loop() {
  long s = 0;
  for (byte i = 0; i < 16; i++) { s += analogRead(LDR); delay(5); }
  float adc = s / 16.0;
  float lux = meter.readLightLevel();                     // the reference
  float estimate = A * pow(adc, B);                       // what the LDR alone would say
  Serial.print(lux, 1); Serial.print(',');
  Serial.print(adc, 1); Serial.print(',');
  Serial.println(estimate, 1);
  delay(500);
}

What the serial monitor should show

Open the serial monitor at the baud rate in the code. This is what our simulator prints for a virtual Arduino Uno with its sensors at their default values. Your numbers will follow your real readings, but the format should match.

lux,adc,estimate
0.0,511.9,0.0
0.0,512.0,0.0
0.0,512.1,0.0
0.0,511.9,0.0
0.0,511.7,0.0

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Dark roomLow lux and low ADC
Lamp closerBoth rise
Spreadsheet curveBends strongly rather than being a straight line
Fitted estimateClose to the BH1750 within about 20 percent in the range tested

If it does not work

BH1750 reads 0

Check the I2C wiring and address.

ADC saturates

The room is too bright for the 10 kΩ resistor. Try a different value.

Fit is poor

Use more points and keep the lamp type the same.

Readings jump

Keep other light sources constant.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the LDR versus lux sensor comparison lab?

Arduino Uno R3, LDR Photoresistor, Resistor 10 kΩ, BH1750 light sensor, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm).

How long does the LDR versus lux sensor comparison lab take to build?

About 60 minutes for a beginner maker, in 6 steps.

How do I know the LDR versus lux sensor comparison lab works?

Dark room: Low lux and low ADC. Lamp closer: Both rise. Spreadsheet curve: Bends strongly rather than being a straight line.

BH1750 reads 0: what should I check?

Check the I2C wiring and address.

ADC saturates: what should I check?

The room is too bright for the 10 kΩ resistor. Try a different value.

Fit is poor: what should I check?

Use more points and keep the lamp type the same.

Readings jump: what should I check?

Keep other light sources constant.