Projects / Washing machine done notifier

Washing machine done notifier

Beginner1.5 hGuided buildReviewed

Build it step by step

0 of 6 done
  1. ESP3220

    Wire the sensor

    Connect the ADXL345 to the ESP32-C3 as in the table.

  2. ESP32

    Check the sensor

    Upload and open the Serial Monitor at 115200 to see "Running" when you shake the board.

  3. ESP32

    Mount

    Stick the box on the side of the machine with double-sided tape or a magnet.

  4. ESP32

    Tune the threshold

    Run a short wash and raise or lower THRESHOLD until it only counts the real wash.

  5. ESP32

    Add the notification

    Put your Wi-Fi details and a notification address in the placeholders and test by shaking for a minute then leaving it.

  6. ESP32

    Run a full cycle

    Check you get one message about five minutes after the spin ends.

In short

How do you build a washing machine done notifier?

A vibration sensor on the washing machine sends a phone message when it has stopped shaking for five minutes. You need ESP32-C3 SuperMini, ADXL345 accelerometer, USB A to USB-C cable (data) and 5 V 2 A USB adapter. It takes 6 steps and about 90 minutes.

Level
Beginner
Time
About 90 min
Parts
4

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
ADXL345 VCCESP32-C3 3V3Power
ADXL345 GNDESP32-C3 GNDGround
ADXL345 SDAESP32-C3 GPIO8I2C data
ADXL345 SCLESP32-C3 GPIO9I2C clock
USB-C cable5 V USB adapterPower

Code

Arduino IDE with the ESP32 boards package, board "ESP32C3 Dev Module" with USB CDC On Boot enabled. Install "Adafruit ADXL345" and "Adafruit Unified Sensor". Put your own Wi-Fi name, password and notification address in the placeholders and never share them in public code. The reading is one sample per second, so the vibration test runs a little slower than the machine's real motion; the average line removes gravity and tilt.

Runs on a virtual ESP32-C3 in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

#include <WiFi.h>
#include <WiFiClientSecure.h>
#include <HTTPClient.h>
#include <Wire.h>
#include <Adafruit_Sensor.h>
#include <Adafruit_ADXL345_U.h>

const char* WIFI_NAME = "YOUR_WIFI_NAME";
const char* WIFI_PASSWORD = "YOUR_WIFI_PASSWORD";
const char* WEBHOOK_URL = "https://YOUR_NOTIFICATION_URL";   // for example a push service topic you created

Adafruit_ADXL345_Unified accel(12345);
const float THRESHOLD = 0.15;       // m/s2 above the resting reading counts as shaking
float avg = 9.81;
unsigned int highSecs = 0, stillSecs = 0;
bool running = false;

void notify() {
  WiFiClientSecure client;
  client.setInsecure();              // no certificate check: fine for a harmless alert, a trade-off
  HTTPClient http;
  if (http.begin(client, WEBHOOK_URL)) {
    http.addHeader("Content-Type", "text/plain");
    http.POST("The washing machine has finished");
    http.end();
  }
}

void setup() {
  Serial.begin(115200);
  Wire.begin(8, 9);
  if (!accel.begin()) { Serial.println("ADXL345 not found"); while (true) delay(1000); }
  accel.setRange(ADXL345_RANGE_2_G);
  WiFi.begin(WIFI_NAME, WIFI_PASSWORD);
  while (WiFi.status() != WL_CONNECTED) delay(500);
}

void loop() {
  sensors_event_t e;
  accel.getEvent(&e);
  float mag = sqrt(e.acceleration.x * e.acceleration.x + e.acceleration.y * e.acceleration.y + e.acceleration.z * e.acceleration.z);
  avg = 0.95 * avg + 0.05 * mag;                   // slow average of the resting value
  float v = fabs(mag - avg);

  if (v > THRESHOLD) { highSecs++; stillSecs = 0; }
  else { stillSecs++; if (stillSecs > 30 && !running) highSecs = 0; }

  if (!running && highSecs >= 60) { running = true; Serial.println("Running"); }
  if (running && stillSecs >= 300) { Serial.println("Done"); notify(); running = false; highSecs = 0; }
  delay(1000);
}

What the serial monitor should show

Open the serial monitor at the baud rate in the code. This is what our simulator prints for a virtual ESP32-C3 DevKitM-1 with its sensors at their default values. Your numbers will follow your real readings, but the format should match.

ADXL345 not found

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Machine offSerial stays quiet
Machine washing for a minuteSerial prints Running
Machine stops for 5 minutesSerial prints Done and the phone alert arrives
Soak pause of 2 minutes mid-washNo false alert

If it does not work

ADXL345 not found

Check SDA on GPIO8, SCL on GPIO9 and 3V3 power.

Never reaches Running

Lower THRESHOLD or stick the sensor on a flatter, more rigid panel.

Alerts too early

Increase the 300 second still time or the soak-pause allowance.

No phone message

Check Wi-Fi, the notification address and that the router lets the ESP32 reach the internet.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the washing machine done notifier?

ESP32-C3 SuperMini, ADXL345 accelerometer, USB A to USB-C cable (data) and 5 V 2 A USB adapter.

How long does the washing machine done notifier take to build?

About 90 minutes for a beginner maker, in 6 steps.

How do I know the washing machine done notifier works?

Machine off: Serial stays quiet. Machine washing for a minute: Serial prints Running. Machine stops for 5 minutes: Serial prints Done and the phone alert arrives.

ADXL345 not found: what should I check?

Check SDA on GPIO8, SCL on GPIO9 and 3V3 power.

Never reaches Running: what should I check?

Lower THRESHOLD or stick the sensor on a flatter, more rigid panel.

Alerts too early: what should I check?

Increase the 300 second still time or the soak-pause allowance.

No phone message: what should I check?

Check Wi-Fi, the notification address and that the router lets the ESP32 reach the internet.