Projects / Knight Rider LED scanner

Knight Rider LED scanner

Beginner45 minGuided buildReviewed

Build it step by step

0 of 6 done
  1. NANO8.5 mA

    Place the LEDs

    Push eight LEDs in a row on the breadboard, all short legs towards the ground rail.

  2. NANO

    Add the resistors

    Put a 220 Ω resistor between each long leg and its own wire to D2 to D9.

  3. NANO

    Wire the ground

    Join the ground rail to Nano GND.

  4. NANO

    Add the speed pot

    Outer pins to 5V and GND, middle pin to A0.

  5. NANO

    Upload and run

    Upload the sketch. The bright dot should sweep with a fading tail.

  6. NANO

    Tune it

    Turn the pot for speed. Change the 3 in the fade line for a longer or shorter tail.

In short

How do you build a knight Rider LED scanner?

Eight LEDs sweep back and forth with a fading tail, like the scanner on a famous TV car, with a pot that sets the speed. You need Arduino Nano, LED 5 mm red × 8, Resistor 220 Ω × 8, Potentiometer 10 kΩ, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 6 steps and about 45 minutes.

Level
Beginner
Time
About 45 min
Parts
6

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
LED 1 to LED 8 anodes (long legs)Nano D2 to D9, each through a 220 Ω resistorOne pin per LED
All LED cathodes (short legs)Nano GNDCommon ground rail
Pot outer pinsNano 5V and GNDSpeed control supply
Pot middle pinNano A0Speed reading

Code

Arduino IDE, board "Arduino Nano" (processor ATmega328P, or ATmega328P (Old Bootloader) for clones). No libraries. The fast loop gives the PWM, so avoid delay() anywhere in it.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

const byte pins[8] = {2, 3, 4, 5, 6, 7, 8, 9};
byte level[8];                 // brightness 0 to 15 for each LED
int pos = 0, dir = 1;
unsigned long lastStep = 0;
byte phase = 0;

void setup() {
  for (byte i = 0; i < 8; i++) pinMode(pins[i], OUTPUT);
}

void loop() {
  unsigned int stepMs = map(analogRead(A0), 0, 1023, 20, 150);
  if (millis() - lastStep >= stepMs) {
    lastStep = millis();
    for (byte i = 0; i < 8; i++) level[i] = level[i] > 3 ? level[i] - 3 : 0;   // fade the tail
    level[pos] = 15;                                                            // bright head
    pos += dir;
    if (pos == 7 || pos == 0) dir = -dir;                                       // bounce at the ends
  }
  phase = (phase + 1) & 15;                                                     // software PWM, 16 steps
  for (byte i = 0; i < 8; i++) digitalWrite(pins[i], level[i] > phase);
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Pot at minimumThe sweep is fast, about one pass in 160 ms
Pot at maximumThe sweep is slow, about one pass in 1.2 s
Look at the tailTwo or three LEDs behind the head are dimmer
Each LED with the sketch stoppedLights fully when its pin is driven HIGH

If it does not work

One LED never lights

It is the wrong way round or its resistor is not in the row. Flip it and check the wire to its pin.

No fading, LEDs just blink

A delay() was added to the loop, which slows the software PWM. Remove it.

The tail flickers

The loop is too slow. Avoid Serial printing inside loop.

Speed does not change

Check the pot's middle pin goes to A0 and the outer pins to 5V and GND.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the knight Rider LED scanner?

Arduino Nano, LED 5 mm red × 8, Resistor 220 Ω × 8, Potentiometer 10 kΩ, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm).

How long does the knight Rider LED scanner take to build?

About 45 minutes for a beginner maker, in 6 steps.

How do I know the knight Rider LED scanner works?

Pot at minimum: The sweep is fast, about one pass in 160 ms. Pot at maximum: The sweep is slow, about one pass in 1.2 s. Look at the tail: Two or three LEDs behind the head are dimmer.

One LED never lights: what should I check?

It is the wrong way round or its resistor is not in the row. Flip it and check the wire to its pin.

No fading, LEDs just blink: what should I check?

A delay() was added to the loop, which slows the software PWM. Remove it.

The tail flickers: what should I check?

The loop is too slow. Avoid Serial printing inside loop.

Speed does not change: what should I check?

Check the pot's middle pin goes to A0 and the outer pins to 5V and GND.