Projects / Keypad tone dialer

Keypad tone dialer

Beginner1 hGuided buildReviewed

Build it step by step

0 of 8 done
  1. NANO

    Install the library

    Add Keypad by Mark Stanley.

  2. NANO

    Find the pins

    Use continuity to find rows and columns.

  3. NANO

    Wire the keypad

    Rows to D2 to D5, columns to D6 to D8.

  4. NANO

    Wire the buzzer

    Plus to D9, minus to GND.

  5. NANO

    Upload the sketch

    Press keys and watch the serial monitor.

  6. NANO

    Play notes

    Keys 1 to 0 play a scale.

  7. NANO

    Record a tune

    Press star, play up to sixteen keys, press star.

  8. NANO

    Play it back

    Press hash.

In short

How do you build a keypad tone dialer?

A phone-style keypad plays a different tone for each key, like a toy telephone. You need Arduino Nano, Keypad 4x3 (membrane), Passive buzzer and Breadboard 830 Tie Points. It takes 8 steps and about 60 minutes.

Level
Beginner
Time
About 60 min
Parts
4

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Keypad row pins 1 to 4Nano D2, D3, D4, D5Find rows and columns with a multimeter on continuity first
Keypad column pins 1 to 3Nano D6, D7, D8Same check
Buzzer plusNano D9Passive buzzer
Buzzer minusNano GNDCommon ground

Code

A 4 by 3 membrane keypad is just twelve switches arranged in a grid of three columns and four rows. The sketch uses the Keypad library, which sets the rows and columns one at a time, finds which key connects them and returns the key as a character. Each of the keys from 1 to 0 is given a note from a musical scale, so the keypad plays a short tune like a toy telephone. A passive buzzer is used because it plays whatever tone the board sends it, which an active buzzer cannot do. The star key starts and stops recording up to sixteen notes, with a high beep when recording starts and a lower one when it stops, and the hash key plays the recording back. Keypad connectors are not standardised, so find the row and column pins first: with a multimeter in continuity mode, press key 1 and see which two pins beep together, then key 2 and so on, and you will see the pattern of three columns and four rows. If the keys come out in the wrong order, swap the pin lists in the sketch.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

#include <Keypad.h>

const byte ROWS = 4, COLS = 3;
char keys[ROWS][COLS] = {
  {'1', '2', '3'},
  {'4', '5', '6'},
  {'7', '8', '9'},
  {'*', '0', '#'}
};
byte rowPins[ROWS] = {2, 3, 4, 5};
byte colPins[COLS] = {6, 7, 8};
Keypad pad = Keypad(makeKeymap(keys), rowPins, colPins, ROWS, COLS);

const int BUZ = 9;
const int NOTES[10] = {262, 294, 330, 349, 392, 440, 494, 523, 587, 659};   // C4 up to E5

byte rec[16];
int recLen = 0;
bool recording = false;

int noteIndex(char k) { return (k == '0') ? 9 : (k - '1'); }

void playKey(char k) {
  tone(BUZ, NOTES[noteIndex(k)], 250);
  delay(300);
}

void setup() {
  pinMode(BUZ, OUTPUT);
  Serial.begin(9600);
}

void loop() {
  char k = pad.getKey();
  if (!k) return;
  Serial.println(k);

  if (k == '*') {                       // start or stop recording a short tune
    recording = !recording;
    if (recording) recLen = 0;
    tone(BUZ, recording ? 1000 : 500, 150);
    delay(200);
  } else if (k == '#') {                // play the recorded tune
    for (int i = 0; i < recLen; i++) playKey(rec[i]);
  } else {
    playKey(k);
    if (recording && recLen < 16) rec[recLen++] = k;
  }
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Press 1Low note and a 1 in the monitor
Press 0The highest note
Star then a few keys then starHigh beep, then low beep
Press hashThe tune plays back
More than sixteen keysExtra keys are not recorded

If it does not work

Wrong keys appear

Swap rows and columns or reverse the pin lists.

Nothing happens

Check every wire and that the keypad is not shifted by one pin.

No sound

Check the buzzer polarity and that it is a passive type.

Two keys at once

Keypads can only report one key at a time, press one.

Reads random keys

A loose wire, press it firmly into the header.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the keypad tone dialer?

Arduino Nano, Keypad 4x3 (membrane), Passive buzzer and Breadboard 830 Tie Points.

How long does the keypad tone dialer take to build?

About 60 minutes for a beginner maker, in 8 steps.

How do I know the keypad tone dialer works?

Press 1: Low note and a 1 in the monitor. Press 0: The highest note. Star then a few keys then star: High beep, then low beep.

Wrong keys appear: what should I check?

Swap rows and columns or reverse the pin lists.

Nothing happens: what should I check?

Check every wire and that the keypad is not shifted by one pin.

No sound: what should I check?

Check the buzzer polarity and that it is a passive type.

Two keys at once: what should I check?

Keypads can only report one key at a time, press one.