Build it step by step
0 of 7 donePlace the JFET
Check the pin order of your part.
Bias the gate
Two 1 MΩ resistors to half supply.
Add the source resistor
10 kΩ to ground.
Couple the input and output
100 nF in, 10 µF out.
Measure the bias
Source voltage is stable.
Compare with and without
Use a piezo pickup and an amplifier.
Box it
Fit it in a small metal box.
How do you build a JFET buffer and preamp?
A 2N3819 JFET buffer gives a high input impedance for guitars and piezo pickups. You need 2N3819 N-channel JFET, Resistor 1 MΩ × 2, Resistor 10 kΩ, Ceramic Capacitor 100 nF × 2, Electrolytic capacitor 10 µF, Audio jack 3.5 mm (PCB, stereo) × 2, 9 V battery, 9 V battery snap with DC jack and Perfboard (dot PCB) 7 × 9 cm. It takes 7 steps and about 90 minutes.
- Level
- Intermediate
- Time
- About 90 min
- Parts
- 9
Parts list
- Semiconductors
- PassivesBuyResistor 1 MΩ × 2
- PassivesBuyResistor 10 kΩ × 1
- PassivesBuy
- PassivesBuy
- ConnectorsBuy
- BatteriesBuy9 V battery × 1
- PowerBuy
- PrototypingBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| 9 V battery plus | Switch, then supply rail | Power |
| Two 1 MΩ resistors | Rail to gate to ground | Bias the gate at half supply |
| Input jack tip | 100 nF capacitor to the gate | AC-coupled input |
| JFET drain | Supply rail | Drain tied to supply |
| JFET source | 10 kΩ resistor to ground | Source resistor |
| JFET source | 10 µF capacitor to the output jack tip | AC-coupled output |
| Jack sleeves and battery minus | Ground | Common ground |
No code needed
A source follower has gain just under one, so it does not make the signal bigger; it keeps the signal from being loaded down. The two 1 MΩ resistors set the gate at half supply and also set the input impedance at about 500 kΩ, much higher than a typical amplifier input, so a piezo pickup or guitar keeps its full tone. Measure the source voltage with a multimeter; it should sit a couple of volts above the gate minus the threshold, and adjust the source resistor until the output swings equally up and down. JFETs vary a lot between parts, so values need small tuning. Use a 9 V battery only, and put the circuit in a small metal box with the jacks for low hum. Switch off by unplugging the input jack if you wire a switching jack.
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| Source voltage | Stable and a few volts above ground |
| Input impedance | Much higher than the amplifier alone |
| Piezo pickup | Fuller, louder sound |
| Hum | Low when boxed and grounded |
If it does not work
No signal
Check the pin order and the output capacitor polarity.
Distorted output
Re-tune the source resistor.
Hum
Use a metal box and keep wires short.
Noisy
Use fresh battery and short gate lead.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the JFET buffer and preamp?
2N3819 N-channel JFET, Resistor 1 MΩ × 2, Resistor 10 kΩ, Ceramic Capacitor 100 nF × 2, Electrolytic capacitor 10 µF, Audio jack 3.5 mm (PCB, stereo) × 2, 9 V battery, 9 V battery snap with DC jack and Perfboard (dot PCB) 7 × 9 cm.
How long does the JFET buffer and preamp take to build?
About 90 minutes for a intermediate maker, in 7 steps.
How do I know the JFET buffer and preamp works?
Source voltage: Stable and a few volts above ground. Input impedance: Much higher than the amplifier alone. Piezo pickup: Fuller, louder sound.
No signal: what should I check?
Check the pin order and the output capacitor polarity.
Distorted output: what should I check?
Re-tune the source resistor.
Hum: what should I check?
Use a metal box and keep wires short.
Noisy: what should I check?
Use fresh battery and short gate lead.
