Build it step by step
0 of 7 doneBuild the 555 oscillator
Fixed resistor and capacitor first.
Hear the tone
Buzzer on the output.
Put the probes in the timing path
Replace the second resistor.
Short the probes
High tone.
Try resistors
100 ohm, 1 k, 10 k.
Check wires and fuses
Good ones sound.
Label the pitches
A table on the lid.
How do you build a continuity tester with tone?
A tester beeps for a short circuit, with a tone that rises as resistance falls. You need NE555 Timer IC, Passive buzzer, Resistor 1 kΩ × 2, Ceramic Capacitor 100 nF, BC547 NPN transistor, Battery holder 4 × AA with switch, AA alkaline battery × 4 and Crocodile clip test leads (10 pack). It takes 7 steps and about 45 minutes.
- Level
- Beginner
- Time
- About 45 min
- Parts
- 8
Parts list
- Integrated CircuitsBuyNE555 Timer IC × 1
- Motors & ActuatorsBuyPassive buzzer × 1
- PassivesBuyResistor 1 kΩ × 2
- PassivesBuy
- SemiconductorsBuy
- PowerBuy
- BatteriesBuy
- Connectors
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| 4 AA holder plus | NE555 pin 8 and pin 4, and the buzzer plus | 6 V supply |
| 4 AA holder minus | NE555 pin 1 and BC547 emitter | Ground |
| 1 k resistor R1 | Between 6 V and NE555 pin 7 | Timing |
| Probe terminals | Between NE555 pin 7 and pins 6 and 2 (joined) | The part you test is the second timing resistor |
| 100 nF capacitor | NE555 pins 6 and 2 to ground | Timing capacitor |
| NE555 pin 3 | 1 k resistor to BC547 base | Output drive |
| BC547 collector | Buzzer minus | Switches the buzzer |
No code needed
A 555 timer makes a tone whose pitch depends on the resistors around it, and here the two probes are one of those resistors. Touch them together and the resistance is almost zero, so the tone is high; connect a wire or fuse with a little resistance and the tone is lower; open circuit and the 555 stops oscillating, so there is silence. That is a continuity tester you can listen to while your eyes stay on the probes. The transistor boosts the 555's output to drive the buzzer. Use the passive (unpowered) buzzer, because it needs a signal from the 555, and keep the supply at 5 to 6 V, since a plain NE555 does not run from two cells. Test only parts and wires that are disconnected from any supply, and discharge capacitors first, because a charged circuit can damage the tester or you. Do not use it on mains wiring. There is no code for this build.
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| Probes shorted | High pitch |
| 1 k resistor | Lower pitch |
| Open probes | Silence |
| A blown fuse | Silence |
If it does not work
No sound
Check the supply is above 4.5 V and the buzzer is passive.
Always sounding
Check pin 2 and 6 are tied together.
Weak tone
Use the BC547 stage and a fresh battery.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the continuity tester with tone?
NE555 Timer IC, Passive buzzer, Resistor 1 kΩ × 2, Ceramic Capacitor 100 nF, BC547 NPN transistor, Battery holder 4 × AA with switch, AA alkaline battery × 4 and Crocodile clip test leads (10 pack).
How long does the continuity tester with tone take to build?
About 45 minutes for a beginner maker, in 7 steps.
How do I know the continuity tester with tone works?
Probes shorted: High pitch. 1 k resistor: Lower pitch. Open probes: Silence.
No sound: what should I check?
Check the supply is above 4.5 V and the buzzer is passive.
Always sounding: what should I check?
Check pin 2 and 6 are tied together.
Weak tone: what should I check?
Use the BC547 stage and a fresh battery.
