Projects / Insect trap counter

Insect trap counter

An IR sensor across the funnel of a light trap counts the insects that fall through each night, and a Nano with a clock and a card writes the hourly totals, so a farmer can watch pest numbers rise and fall.

Intermediate2.5 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. NANO

    Wire the sensor

    VCC to 5V, GND to GND, OUT to D2.

  2. NANO

    Wire the clock

    SDA to A4, SCL to A5, power and ground.

  3. NANOMICROS

    Wire the card module

    CS D10, MOSI D11, MISO D12, SCK D13, 5V and GND.

  4. NANO13.5 mA

    Wire the light

    Red LED through 220 ohms to D6.

  5. NANODS323121:23

    Install the library

    RTClib.

  6. NANO

    Upload the sketch

    The light stays off.

  7. NANO

    Wave a small object in front of the sensor

    The light blinks and the Serial Monitor counts.

In short

How do you build an insect trap counter?

An IR sensor across the funnel of a light trap counts the insects that fall through each night, and a Nano with a clock and a card writes the hourly totals, so a farmer can watch pest numbers rise and fall. You need Arduino Nano, IR obstacle avoidance sensor module, DS3231 RTC module, MicroSD Card Module, LED 5 mm red, Resistor 220 Ω, Jumper wires male to male (40 pcs, 20 cm) and Breadboard 830 Tie Points. It takes 7 steps and about 150 minutes.

Level
Intermediate
Time
About 150 min
Parts
8

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
IR sensor VCCNano 5VPower at 5 V
IR sensor GNDNano GNDCommon ground
IR sensor OUTNano D2Low when something passes in front
DS3231 SDA and SCLNano A4 and A5I2C, address 0x68 (VCC to 5V, GND to GND)
SD module CSNano D10Chip select
SD module MOSI, MISO, SCKNano D11, D12, D13SPI (VCC to 5V, GND to GND, use a 5 V module)
Red LED long leg220 ohm resistor to Nano D6Blinks on each count and stays on for a card problem
Red LED short legNano GNDReturn

Code

A light trap uses a lamp to draw night-flying insects, which fall through a funnel into a container. Counting them each night shows whether a pest is increasing, and this helps decide when to treat the crop, which is the idea behind integrated pest management. An IR obstacle sensor sends out infrared light and sees it bounce back from anything in front, so each insect passing in front of it makes the output go low for a moment. The program counts each change from high to low, with a pause of 60 milliseconds so that one insect is not counted twice, and writes the total for each hour, with the date, to a file on the card when the hour changes. The clock chip keeps good time, and the sketch sets it to the time of upload the first time. It will not tell the kinds of insects apart, so count a sample by eye now and then to see how well it matches, and expect it to miss clusters and tiny insects. Bright sun or the trap lamp can confuse an IR module, so shade the sensor from the lamp and test it at night. Keep the electronics in a dry, shaded box. Do not touch a mains lamp or its wiring, and use a lamp made for the purpose, with its own safe supply.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

#include <Wire.h>
#include <SPI.h>
#include <SD.h>
#include <RTClib.h>

const int IR = 2, LED = 6, CS_PIN = 10;
RTC_DS3231 rtc;

unsigned int hourCount = 0;
int currentHour = -1;
bool lastState = HIGH;
unsigned long lastCount = 0;

void writeHour(DateTime t, unsigned int n) {
  File f = SD.open("TRAP.CSV", FILE_WRITE);
  if (!f) { digitalWrite(LED, HIGH); return; }
  f.print(t.year()); f.print('-'); f.print(t.month()); f.print('-'); f.print(t.day()); f.print(' ');
  f.print(t.hour()); f.print(F(":00,"));
  f.println(n);
  f.close();                                       // saved, even if the power goes after this
}

void setup() {
  pinMode(IR, INPUT);
  pinMode(LED, OUTPUT);
  Serial.begin(9600);
  if (!rtc.begin()) { digitalWrite(LED, HIGH); while (true) {} }
  if (rtc.lostPower()) rtc.adjust(DateTime(F(__DATE__), F(__TIME__)));
  if (!SD.begin(CS_PIN)) { digitalWrite(LED, HIGH); while (true) {} }
  File f = SD.open("TRAP.CSV", FILE_WRITE);
  if (f) {
    if (f.size() == 0) f.println(F("hour,count"));
    f.close();
  }
  currentHour = rtc.now().hour();
}

void loop() {
  bool state = digitalRead(IR);                    // the sensor output goes low when something is in front
  if (state == LOW && lastState == HIGH && millis() - lastCount > 60) {
    hourCount++;
    lastCount = millis();
    digitalWrite(LED, HIGH);
    delay(15);
    digitalWrite(LED, LOW);
    Serial.println(hourCount);
  }
  lastState = state;

  static unsigned long lastCheck = 0;
  if (millis() - lastCheck > 1000) {               // check the clock once a second
    lastCheck = millis();
    DateTime now = rtc.now();
    if (now.hour() != currentHour) {
      writeHour(now - TimeSpan(0, 1, 0, 0), hourCount);   // save the hour that has just ended
      hourCount = 0;
      currentHour = now.hour();
    }
  }
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
StartNo light, no errors
Pass a finger in front of the sensorBlink and count 1
Pass it twice quicklyTwo counts, not more
Wait for the next hourA line in TRAP.CSV
Remove the cardRed light stays on

If it does not work

Counts by itself

Shade the sensor from the lamp and from sun, and turn down its sensitivity.

Never counts

Check OUT on D2 and turn up the sensitivity screw.

Red light on

Check the card is FAT32 and wired to D10 to D13.

Wrong hour

Set the clock again, or re-upload.

File is empty

Wait for the hour to change, then remove the card.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the insect trap counter?

Arduino Nano, IR obstacle avoidance sensor module, DS3231 RTC module, MicroSD Card Module, LED 5 mm red, Resistor 220 Ω, Jumper wires male to male (40 pcs, 20 cm) and Breadboard 830 Tie Points.

How long does the insect trap counter take to build?

About 150 minutes for a intermediate maker, in 7 steps.

How do I know the insect trap counter works?

Start: No light, no errors. Pass a finger in front of the sensor: Blink and count 1. Pass it twice quickly: Two counts, not more.

Counts by itself: what should I check?

Shade the sensor from the lamp and from sun, and turn down its sensitivity.

Never counts: what should I check?

Check OUT on D2 and turn up the sensitivity screw.

Red light on: what should I check?

Check the card is FAT32 and wired to D10 to D13.

Wrong hour: what should I check?

Set the clock again, or re-upload.