Projects / Wireless indoor-outdoor thermometer

Wireless indoor-outdoor thermometer

Intermediate2 hGuided buildReviewed

Build it step by step

0 of 6 done
  1. NANODS18B2026.8°C

    Test the sensor

    Read the DS18B20 on the outdoor Nano with the Serial Monitor.

  2. NANO

    Fit the antennas

    Solder a 17 cm wire to each radio board's antenna pad.

  3. NANO433

    Send a test

    Upload the outdoor sketch and check the indoor board receives a number.

  4. NANO433HelloPCF8574

    Add the display

    Wire the LCD and show the temperature and the min and max.

  5. NANO433

    Test the warning

    Switch off the outdoor board for 5 minutes and see the message.

  6. NANO

    Mount outdoors

    Put the outdoor box in the shade away from direct sun.

In short

How do you build a wireless indoor-outdoor thermometer?

An outdoor Nano sends temperature over a cheap 433 MHz link to an indoor display, like a shop-bought weather clock. You need Arduino Nano × 2, 433 MHz RF transmitter and receiver pair, DS18B20 waterproof probe, Resistor 4.7 kΩ, 16x2 LCD with I2C backpack (PCF8574), Battery holder 4 × AA with switch and AA alkaline battery × 4. It takes 6 steps and about 120 minutes.

Level
Intermediate
Time
About 120 min
Parts
7

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Outdoor: DS18B20 red, black, yellowNano 5V, GND, D2, with 4.7 kΩ from D2 to 5VOutdoor probe
Outdoor: 433 MHz transmitter VCC, GND, DATANano 5V, GND, D12Radio
Outdoor: 17 cm wire on the transmitter ANT padStraight wireQuarter-wave antenna
Outdoor: 4 AA holderNano VIN and GNDAbout 6 V supply
Indoor: 433 MHz receiver VCC, GND, DATANano 5V, GND, D11Radio
Indoor: 17 cm wire on the receiver ANT padStraight wireQuarter-wave antenna
Indoor: LCD SDA, SCL, VCC, GNDNano A4, A5, 5V, GNDI2C display
Indoor: USB cableIndoor NanoPower

Code

Arduino IDE, board "Arduino Nano" (processor ATmega328P, or ATmega328P (Old Bootloader) for clones). Install "RadioHead" and, for the outdoor board, "OneWire" and "DallasTemperature"; the indoor board also needs "LiquidCrystal I2C". Cut each antenna to 17 cm (a quarter wave at 433 MHz) and keep it straight and away from metal. The outdoor Nano runs from four AA cells through its VIN pin; fresh cells give about 6.4 V and it keeps running until about 5.8 V. Put the transmitter in a dry box and bring the probe out through a cable gland. Range through walls is typically 20 to 50 m.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

// ---- Outdoor sketch (Nano with the transmitter) ----
#include <RH_ASK.h>
#include <SPI.h>
#include <OneWire.h>
#include <DallasTemperature.h>

RH_ASK driver(2000, 11, 12, 10);           // speed, rx pin, tx pin, ptt pin
OneWire oneWire(2);
DallasTemperature sensors(&oneWire);

void setup() { driver.init(); sensors.begin(); }

void loop() {
  sensors.requestTemperatures();
  float t = sensors.getTempCByIndex(0);
  char msg[16];
  dtostrf(t, 4, 1, msg);                    // for example " 23.4"
  driver.send((uint8_t*)msg, strlen(msg));
  driver.waitPacketSent();
  delay(60000);                             // once a minute
}

/* ---- Indoor sketch (Nano with the receiver and LCD) ----
#include <RH_ASK.h>
#include <SPI.h>
#include <Wire.h>
#include <LiquidCrystal_I2C.h>
RH_ASK driver(2000, 11, 12, 10);
LiquidCrystal_I2C lcd(0x27, 16, 2);
float minT = 99, maxT = -99;
unsigned long lastRx = 0;
void setup() { driver.init(); lcd.init(); lcd.backlight(); lcd.print("Waiting..."); }
void loop() {
  uint8_t buf[16]; uint8_t len = sizeof(buf);
  if (driver.recv(buf, &len)) {              // RadioHead checks the checksum for us
    buf[len] = 0;
    float t = atof((char*)buf);
    lastRx = millis();
    minT = min(minT, t); maxT = max(maxT, t);
    lcd.clear();
    lcd.setCursor(0, 0); lcd.print("Out "); lcd.print(t, 1); lcd.print(" C");
    lcd.setCursor(0, 1); lcd.print("L"); lcd.print(minT, 0); lcd.print(" H"); lcd.print(maxT, 0);
  }
  if (lastRx && millis() - lastRx > 300000UL) { lcd.setCursor(0, 1); lcd.print("No signal 5 min "); }
}
*/

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Boards a few metres apartTemperature shown within a minute
Outdoor probe in warm handReading rises on the next packet
Outdoor board offNo signal message after 5 minutes
Min and maxUpdate as the day goes on

If it does not work

Nothing received

Check the data pins match (TX on D12, RX on D11) and the antennas.

Garbage numbers

RadioHead should reject bad packets. Check the baud match and keep the antenna clear.

Reads -127

DS18B20 not found. Check the pull-up.

Short range

Fit the antennas straight and move away from metal and switching supplies.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the wireless indoor-outdoor thermometer?

Arduino Nano × 2, 433 MHz RF transmitter and receiver pair, DS18B20 waterproof probe, Resistor 4.7 kΩ, 16x2 LCD with I2C backpack (PCF8574), Battery holder 4 × AA with switch and AA alkaline battery × 4.

How long does the wireless indoor-outdoor thermometer take to build?

About 120 minutes for a intermediate maker, in 6 steps.

How do I know the wireless indoor-outdoor thermometer works?

Boards a few metres apart: Temperature shown within a minute. Outdoor probe in warm hand: Reading rises on the next packet. Outdoor board off: No signal message after 5 minutes.

Nothing received: what should I check?

Check the data pins match (TX on D12, RX on D11) and the antennas.

Garbage numbers: what should I check?

RadioHead should reject bad packets. Check the baud match and keep the antenna clear.

Reads -127: what should I check?

DS18B20 not found. Check the pull-up.

Short range: what should I check?

Fit the antennas straight and move away from metal and switching supplies.