Projects / Hallway motion chime

Hallway motion chime

Beginner1.7 hGuided buildReviewed

Build it step by step

0 of 9 done
  1. NANORCWL0516motion

    Wire the radar

    VIN to 5V, GND to GND and OUT to D2.

  2. NANO

    Wire the buzzer

    Positive through the 1 k resistor to D8, negative to GND.

  3. NANO

    Wire the button

    One leg to D3 and the other to GND.

  4. NANO

    Upload the sketch

    The monitor says Hall chime ready.

  5. NANO

    Wait half a minute

    The sensor settles, so keep still.

  6. NANORCWL0516motion

    Wave your hand 1 m in front

    The monitor prints Motion and the two-note chime plays.

  7. NANO

    Keep waving

    No second chime for 10 seconds.

  8. NANO

    Press the button

    The monitor says Muted, and waving now does nothing.

  9. NANO

    Press it again

    A short blip tells you the chime is back.

In short

How do you build a hallway motion chime?

A small microwave radar sensor notices someone walking into the hall and plays a short two-note chime. A button mutes it for quiet hours, and a lock-out stops it chiming over and over while someone stays in view. You need Arduino Nano, RCWL-0516 microwave radar motion sensor, Passive buzzer, Resistor 1 kΩ, Tactile push button 6 mm, USB A to micro-USB cable (data), Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 9 steps and about 100 minutes.

Level
Beginner
Time
About 100 min
Parts
8

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
RCWL-0516 VIN and GNDNano 5V and GNDPower, it needs 4 to 28 V
RCWL-0516 OUTNano D2Goes HIGH for about 2 seconds when it sees movement
Passive buzzer +1 k resistor to Nano D8The resistor keeps it from being too loud
Passive buzzer -Nano GNDReturn
Mute buttonNano D3 and GNDPress to switch the chime off or on

Code

The RCWL-0516 is a small Doppler radar. It sends out a weak microwave signal and listens for changes in what comes back, so it notices movement even through a plastic box or a thin wall, which a PIR sensor cannot do. When it sees something move it raises its OUT pin to HIGH for about two seconds, and the sketch only reacts to the moment the pin goes from LOW to HIGH. This is called edge detection, and it stops the chime from playing again and again for as long as the signal stays high. After a chime, a lock-out of ten seconds keeps the hall quiet while someone walks about. The chime itself is two notes, A at 880 Hz and then D at 1175 Hz, played with tone(). A passive buzzer is used because it plays whatever frequency you give it, while an active buzzer can only make one fixed sound. The button toggles mute, and it plays a short blip when you switch the chime back on, so you know where you stand. Mounting matters a lot: the radar sees through thin walls and sometimes catches fans, people next door, even a passing car, so point it away from those and try putting a bit of foil behind it. The sensor also needs about 30 seconds after power-up to settle before it is steady. If it chimes too easily you can reduce its sensitivity by adding a small capacitor, but start by moving it.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

const uint8_t RADAR = 2;
const uint8_t BUZZER = 8;
const uint8_t MUTE_BTN = 3;
const unsigned long LOCKOUT = 10000;   // after one chime, stay quiet for 10 seconds

bool muted = false;
bool prevBtn = false;
bool prevRadar = false;
unsigned long lastChime = 0;
bool chimedOnce = false;

void chime() {
  tone(BUZZER, 880, 180);
  delay(220);
  tone(BUZZER, 1175, 350);
  delay(400);
  noTone(BUZZER);
}

void setup() {
  pinMode(RADAR, INPUT);
  pinMode(MUTE_BTN, INPUT_PULLUP);
  pinMode(BUZZER, OUTPUT);
  Serial.begin(9600);
  Serial.println(F("Hall chime ready (radar needs about 30 s to settle)"));
}

void loop() {
  bool b = (digitalRead(MUTE_BTN) == LOW);
  if (b && !prevBtn) {
    muted = !muted;
    Serial.println(muted ? F("Muted") : F("Chime on"));
    if (!muted) { tone(BUZZER, 1000, 80); }       // a short blip shows it is back on
  }
  prevBtn = b;

  bool radar = digitalRead(RADAR);
  if (radar && !prevRadar) {                      // a new detection, not a continuing one
    Serial.println(F("Motion"));
    if (!muted && (!chimedOnce || millis() - lastChime >= LOCKOUT)) {
      chime();
      lastChime = millis();
      chimedOnce = true;
    }
  }
  prevRadar = radar;
  delay(20);
}

What the serial monitor should show

Open the serial monitor at the baud rate in the code. This is what our simulator prints for a virtual Arduino Nano with its sensors at their default values. Your numbers will follow your real readings, but the format should match.

Hall chime ready (radar needs about 30 s to settle)

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Wave once at 1 mMotion printed and one chime
Walk in and stand stillOne chime only, not a stream
Wave again within 10 sMotion printed but no chime
Press the button then waveMotion printed, no chime
Press the button again and wave after 10 sA blip, then a chime
Sit completely still for a minuteNothing is printed

If it does not work

Chimes by itself

The radar sees through the wall, so turn it or put foil behind it.

Never detects

Check VIN has 5 V and OUT goes to D2, and wait 30 seconds after power-up.

Buzzer is too quiet

Make sure it is a passive buzzer on D8 and try a 220 ohm resistor.

Chime plays twice

Your hand moved in and out, so raise LOCKOUT.

Mute button does nothing

Check it goes to D3 and GND and is pressed across its legs.

Upload fails

Choose the Old Bootloader option for the Nano.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the hallway motion chime?

Arduino Nano, RCWL-0516 microwave radar motion sensor, Passive buzzer, Resistor 1 kΩ, Tactile push button 6 mm, USB A to micro-USB cable (data), Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm).

How long does the hallway motion chime take to build?

About 100 minutes for a beginner maker, in 9 steps.

How do I know the hallway motion chime works?

Wave once at 1 m: Motion printed and one chime. Walk in and stand still: One chime only, not a stream. Wave again within 10 s: Motion printed but no chime.

Chimes by itself: what should I check?

The radar sees through the wall, so turn it or put foil behind it.

Never detects: what should I check?

Check VIN has 5 V and OUT goes to D2, and wait 30 seconds after power-up.

Buzzer is too quiet: what should I check?

Make sure it is a passive buzzer on D8 and try a 220 ohm resistor.

Chime plays twice: what should I check?

Your hand moved in and out, so raise LOCKOUT.