Projects / Solder fume extractor

Solder fume extractor

Beginner1 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. ABS

    Cut the box

    Fan opening, filter slot and exit holes.

  2. Mount the fan

    Fit a finger guard.

  3. Fit the speed controller

    Knob on the front.

  4. Wire the supply

    Fuse in the positive lead.

  5. 12.2 mA

    Add the light

    A short strip with its own switch.

  6. Insert the filter

    Fit the carbon sheet in the slot.

  7. Test with solder smoke

    Place it beside the iron.

In short

How do you build a solder fume extractor?

A 12 V fan pulls solder fumes through a carbon filter, with speed control and a work light. You need 12 V DC fan 80 mm, DC motor speed controller (PWM, 10 A), 12 V 2 A DC adapter, 12 V LED strip warm white (5 m, 2835) and ABS project box (100 × 60 × 25 mm). It takes 7 steps and about 60 minutes.

Level
Beginner
Time
About 60 min
Parts
5

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
12 V adapter plusFuse (2 A), then PWM controller IN+Protected supply
12 V adapter minusPWM controller IN−Return
PWM controller OUT+ and OUT−Fan plus and minusVariable fan speed
Adapter plus (after the fuse)Switch, then LED strip plusWork light
Adapter minusLED strip minusReturn

No code needed

A 12 V fan blows air through a box with a slot for an activated-carbon filter sheet, and a small PWM module sets the speed with a knob; PWM switches the fan on and off quickly, so it runs slower without losing torque. A short piece of warm white LED strip on its own switch gives a work light. This is a low-voltage build: use the 12 V adapter with a 2 A fuse in the positive lead and keep the adapter away from heat and the soldering iron. Carbon filters catch some fumes and smells but not everything, and they wear out within a few months of use, so change them regularly and work in a ventilated room with a window open. Solder flux fumes are irritating; lead-free solder and a good extractor reduce, but do not remove, the risk. Place the fan so the air goes away from your face, never leave a hot iron unattended, and never block the fan's air path or put fingers near the blades. Fit a guard grille over the fan. Keep the hot iron stand away from the box and the filter, which can burn.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Switch onFan runs, speed follows the knob
Solder near the intakeSmoke is drawn away from your face
LightSwitches independently
FilterFits snugly with no gaps

If it does not work

Fan will not start slowly

Raise the minimum speed on the controller.

Weak pull

Move the fan closer to the work and check the filter fit.

Controller hot

Use a smaller fan or a larger controller.

Smell persists

Replace the carbon filter and ventilate.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the solder fume extractor?

12 V DC fan 80 mm, DC motor speed controller (PWM, 10 A), 12 V 2 A DC adapter, 12 V LED strip warm white (5 m, 2835) and ABS project box (100 × 60 × 25 mm). 12 V LED strip warm white (5 m, 2835): A short piece as a work light.

How long does the solder fume extractor take to build?

About 60 minutes for a beginner maker, in 7 steps.

How do I know the solder fume extractor works?

Switch on: Fan runs, speed follows the knob. Solder near the intake: Smoke is drawn away from your face. Light: Switches independently.

Fan will not start slowly: what should I check?

Raise the minimum speed on the controller.

Weak pull: what should I check?

Move the fan closer to the work and check the filter fit.

Controller hot: what should I check?

Use a smaller fan or a larger controller.

Smell persists: what should I check?

Replace the carbon filter and ventilate.