Build it step by step
0 of 7 doneBuild the clock
555 astable as in the table. Check the LED on its output blinks about five times a second.
Wire the first flip-flop
CD4013 chip 1, FF1: D to /Q, clock from the 555.
Tie off the set and reset
Pins 4 and 6 (FF1) and pins 8 and 11 (FF2) to GND.
Chain the stages
Q of one to the clock of the next across both chips.
Add the LEDs
Each Q through 1 kΩ to an LED to ground.
Watch
The first LED blinks at about 2.4 Hz, each next at half that rate.
Measure
Use a scope or count blinks in 10 seconds for each LED.
How do you build a frequency divider chain?
Divide a 555 clock by 2, 4, 8 and 16 with flip-flops and see each output on LEDs and a scope. You need NE555 Timer IC, CD4013 dual D flip-flop × 2, Resistor 10 kΩ × 2, Electrolytic capacitor 10 µF, LED 5 mm red × 4, Resistor 1 kΩ × 4, Breadboard 830 Tie Points, Jumper wires male to male (40 pcs, 20 cm), 9 V battery and 9 V battery snap with DC jack. It takes 7 steps and about 45 minutes.
- Level
- Beginner
- Time
- About 45 min
- Parts
- 10
Parts list
- Integrated CircuitsBuyNE555 Timer IC × 1
- Integrated CircuitsBuy
- PassivesBuyResistor 10 kΩ × 2
- PassivesBuy
- SemiconductorsBuyLED 5 mm red × 4
- PassivesBuyResistor 1 kΩ × 4
- PrototypingBuy
- PrototypingBuy
- BatteriesBuy9 V battery × 1
- PowerBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| 9 V battery + | 555 pins 8 and 4, CD4013 pin 14 (both chips) | Supply |
| 9 V battery - | 555 pin 1, CD4013 pin 7 (both chips) | Ground |
| 555 astable | 10 kΩ from +9 V to pin 7, 10 kΩ from pin 7 to pins 2 and 6, 10 µF from pins 2 and 6 to GND | About 4.8 Hz |
| 555 pin 3 (output) | Chip 1 pin 3 (CLK of FF1) | Clock in |
| Each FF: D to its own /Q | Chip pin 5 to pin 2, pin 9 to pin 12 | Toggle (divide by two) |
| Chip 1 pin 1 (Q1) | Chip 1 pin 10 (CLK of FF2) | Chain |
| Chip 1 pin 13 (Q2) | Chip 2 pin 3 (CLK of FF3) | Chain |
| Chip 2 pin 1 (Q3) | Chip 2 pin 10 (CLK of FF4) | Chain |
| Q1 to Q4 | 1 kΩ then LED to GND | Four LEDs: pins 1, 13 on chip 1, 1, 13 on chip 2 |
| All SET and RESET pins (4, 6, 8, 11) | GND | Held inactive |
No code needed
No code. The 555 runs at about 1.44 ÷ ((10 kΩ + 2 × 10 kΩ) × 10 µF) ≈ 4.8 Hz. After each flip-flop the frequency halves: 2.4, 1.2, 0.6 and 0.3 Hz. CD4013 outputs are weak, so use 1 kΩ for the LEDs, which will glow gently.
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| FF1 output | About 2.4 Hz |
| FF2 output | About 1.2 Hz |
| FF4 output | About 0.3 Hz |
| Each LED | Half as fast as the one before |
If it does not work
No blinking
Check the 555 first with a spare LED on pin 3.
LEDs are very dim
CD4013 outputs are weak. Use 1 kΩ or a transistor buffer.
Unstable counting
A SET or RESET pin is floating. Tie them to GND.
Wrong frequencies
Capacitor tolerance. Count blinks to measure the real rate.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the frequency divider chain?
NE555 Timer IC, CD4013 dual D flip-flop × 2, Resistor 10 kΩ × 2, Electrolytic capacitor 10 µF, LED 5 mm red × 4, Resistor 1 kΩ × 4, Breadboard 830 Tie Points, Jumper wires male to male (40 pcs, 20 cm), 9 V battery and 9 V battery snap with DC jack.
How long does the frequency divider chain take to build?
About 45 minutes for a beginner maker, in 7 steps.
How do I know the frequency divider chain works?
FF1 output: About 2.4 Hz. FF2 output: About 1.2 Hz. FF4 output: About 0.3 Hz.
No blinking: what should I check?
Check the 555 first with a spare LED on pin 3.
LEDs are very dim: what should I check?
CD4013 outputs are weak. Use 1 kΩ or a transistor buffer.
Unstable counting: what should I check?
A SET or RESET pin is floating. Tie them to GND.
Wrong frequencies: what should I check?
Capacitor tolerance. Count blinks to measure the real rate.
