Projects / Light sensor fault hunt

Light sensor fault hunt

Beginner50 minGuided buildReviewed

Build it step by step

0 of 7 done
  1. NANO357 lux

    Wire the working divider

    5V to the LDR, the LDR to A0 and the resistor, the resistor to GND.

  2. NANO

    Upload and watch the numbers

    Open the Serial Monitor at 9600 baud.

  3. NANO358 lux

    Cover and uncover the LDR

    The number falls in the dark and rises in the light.

  4. NANO

    Look away while the helper plants a fault

    The readings stick or wander.

  5. NANO

    Measure A0 with the meter

    Compare with the voltage the sketch prints.

  6. NANO

    Trace the wires

    Find the moved resistor, the open ground or the wrong hole.

  7. NANO

    Fix one fault at a time

    Check the readings come back to normal.

In short

How do you build a light sensor fault hunt?

An LDR divider on a Nano should rise and fall with the light, but a planted fault makes it read full or flat. Build it working, have a helper plant faults, and find them by measuring the voltage at the analog pin. You need Arduino Nano, LDR Photoresistor, Resistor 10 kΩ, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 7 steps and about 50 minutes.

Level
Beginner
Time
About 50 min
Parts
5

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
LDR leg 1Nano 5VTop of the divider
LDR leg 2Nano A0 and 10 kilohm resistor leg 1The divider output
10 kilohm resistor leg 2Nano GNDBottom of the divider

Code

The LDR and the 10 kilohm resistor form a voltage divider, so the analog pin sees a voltage that rises as the LDR gets brighter and its resistance falls. In room light the reading is usually somewhere in the middle, in the dark it is near zero, and in strong light it is high. The sketch prints the raw number, the voltage, a bar and a hint if the value is stuck at an end. Fault hunt: build it working and note the readings in light and dark. Then ask a helper to plant one fault at a time while you look away. Safe faults are moving the 10 kilohm resistor to 5 V instead of ground, which makes the pin read high all the time, leaving off the ground end of the resistor, which makes the reading wander, and moving the sensor wire one hole away from A0. Use a meter on the A0 pin and trace each wire to find the cause before you touch anything.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

const uint8_t SENSOR_PIN = A0;

void setup() {
  Serial.begin(9600);
}

void loop() {
  int raw = analogRead(SENSOR_PIN);                  // 0 to 1023
  float volts = raw * 5.0 / 1023.0;
  Serial.print("raw ");
  Serial.print(raw);
  Serial.print("  volts ");
  Serial.print(volts, 2);
  Serial.print("  ");
  for (int i = 0; i < raw / 32; i++) Serial.print('#');   // a quick bar
  Serial.println();

  if (raw > 1000) Serial.println("  Reads full: the pin may be tied to 5 V, or the bottom resistor is missing.");
  if (raw < 20)   Serial.println("  Reads zero: the pin may be tied to ground, or the LDR is not connected.");
  delay(400);
}

What the serial monitor should show

Open the serial monitor at the baud rate in the code. This is what our simulator prints for a virtual Arduino Nano with its sensors at their default values. Your numbers will follow your real readings, but the format should match.

raw 512  volts 2.50  ################
raw 513  volts 2.51  ################
raw 512  volts 2.50  ################
raw 513  volts 2.51  ################
raw 512  volts 2.50  ################
raw 511  volts 2.50  ###############

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Working circuit in room lightA mid-range reading
CoveredClose to zero
Bright torchNear full scale
Resistor to 5 VAlways near 1023
Ground end of the resistor missingReadings wander

If it does not work

Readings never change

The LDR may not be in the divider, so check both legs.

Always zero

Check the LDR leg to 5 V.

Always full

Check the resistor goes to GND, not 5V.

Numbers noisy

Keep the wires short and check the ground end.

Meter and sketch disagree

Check the meter is on DC volts and the probe is on A0.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the light sensor fault hunt?

Arduino Nano, LDR Photoresistor, Resistor 10 kΩ, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm).

How long does the light sensor fault hunt take to build?

About 50 minutes for a beginner maker, in 7 steps.

How do I know the light sensor fault hunt works?

Working circuit in room light: A mid-range reading. Covered: Close to zero. Bright torch: Near full scale.

Readings never change: what should I check?

The LDR may not be in the divider, so check both legs.

Always zero: what should I check?

Check the LDR leg to 5 V.

Always full: what should I check?

Check the resistor goes to GND, not 5V.

Numbers noisy: what should I check?

Keep the wires short and check the ground end.