Projects / Temperature probe fault hunt

Temperature probe fault hunt

Beginner50 minGuided buildReviewed

Build it step by step

0 of 7 done
  1. NANO

    Wire the working circuit

    Red to 5V, black to GND, yellow to D2 with 4.7 kilohms to 5V.

  2. NANO

    Install the libraries

    OneWire and DallasTemperature.

  3. NANO

    Upload and read

    A sensible room temperature appears.

  4. NANO

    Look away while the helper removes the pull-up

    The reading becomes minus 127.

  5. NANO

    Diagnose

    Measure the data pin, which should sit near 5 V when idle.

  6. NANO

    Restore, then the helper moves the data wire

    Again minus 127, and a continuity check finds it.

  7. NANO

    Restore, then the helper pulls the red wire

    The reading may be 85 or minus 127.

In short

How do you build a temperature probe fault hunt?

A DS18B20 probe shows minus 127 or exactly 85 degrees when something is wrong. Build it working, have a helper plant two safe faults, and learn what each strange reading means and how to find the cause. You need Arduino Nano, DS18B20 waterproof probe, Resistor 4.7 kΩ, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm). It takes 7 steps and about 50 minutes.

Level
Beginner
Time
About 50 min
Parts
5

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
DS18B20 red wire (VDD)Nano 5VPower
DS18B20 black wire (GND)Nano GNDCommon ground
DS18B20 yellow wire (DATA)Nano D2One-wire data line
4.7 kilohm resistorBetween D2 and 5VThe pull-up that the one-wire bus needs

Code

The DS18B20 talks on a single data wire that must be held high by a pull-up resistor of about 4.7 kilohms. When the sketch cannot find the sensor, the library returns minus 127. A reading of exactly 85 degrees is the chip's power-on value, which appears when the chip answers but has not completed a measurement, usually because its power is poor or the read came too soon. The sketch prints a plain-language explanation for each case. Fault hunt: build it working first and note the readings, then ask a helper to plant one fault at a time while you look away. Safe faults are taking out the pull-up resistor, moving the data wire to another pin, and pulling out the red power wire so the chip runs on the data line alone. Never plant a reversed power and ground fault on this sensor, because a DS18B20 connected backwards can become very hot and fail. Work out each fault from the symptom and a meter reading on the data pin, and fix them one at a time.

Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

#include <OneWire.h>
#include <DallasTemperature.h>

OneWire oneWire(2);                 // data on D2
DallasTemperature sensors(&oneWire);

void setup() {
  Serial.begin(9600);
  sensors.begin();
  Serial.print("Sensors found: ");
  Serial.println(sensors.getDeviceCount());
}

void loop() {
  sensors.requestTemperatures();
  float t = sensors.getTempCByIndex(0);
  if (t == DEVICE_DISCONNECTED_C) {          // -127.00
    Serial.println("-127: no sensor answering. Check the data wire, the pull-up and the power.");
  } else if (t == 85.0) {
    Serial.println("85: the power-on value. The sensor has not finished a conversion. Check the power and wires.");
  } else {
    Serial.print("Temperature: ");
    Serial.print(t, 1);
    Serial.println(" C");
  }
  delay(1000);
}

What the serial monitor should show

Open the serial monitor at the baud rate in the code. This is what our simulator prints for a virtual Arduino Nano with its sensors at their default values. Your numbers will follow your real readings, but the format should match.

Sensors found: 1
Temperature: 24.5 C

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Working circuitRoom temperature to about one degree
No pull-up-127 with the explanation line
Data wire on the wrong pin-127, and zero sensors found
Power wire removed85 or -127
Warm the probe in your handThe reading rises steadily

If it does not work

Always -127 even when wired correctly

Check the sensor is the 3-wire probe and the wire colours match yours.

Reading stuck at 85

Check the power wire and keep the data wire short.

Sensor gets hot

Disconnect at once and check the power is the right way round.

No serial text

Set 9600 baud in the monitor.

Library errors

Install both libraries.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the temperature probe fault hunt?

Arduino Nano, DS18B20 waterproof probe, Resistor 4.7 kΩ, Breadboard 830 Tie Points and Jumper wires male to male (40 pcs, 20 cm).

How long does the temperature probe fault hunt take to build?

About 50 minutes for a beginner maker, in 7 steps.

How do I know the temperature probe fault hunt works?

Working circuit: Room temperature to about one degree. No pull-up: -127 with the explanation line. Data wire on the wrong pin: -127, and zero sensors found.

Always -127 even when wired correctly: what should I check?

Check the sensor is the 3-wire probe and the wire colours match yours.

Reading stuck at 85: what should I check?

Check the power wire and keep the data wire short.

Sensor gets hot: what should I check?

Disconnect at once and check the power is the right way round.

No serial text: what should I check?

Set 9600 baud in the monitor.