Build it step by step
0 of 7 donePower the chip
Pin 16 to +5 V, pin 8 to GND.
Enable it
Pins 4 and 5 to GND, pin 6 to +5 V. Without this no output goes low.
Make the address switches
Three DIP sections to pins 1, 2 and 3 with pull-downs.
Add the LEDs
Each LED with 330 Ω from +5 V to its output pin.
Set an address
Switch to binary 101 (5) and see LED 5 light.
Count through all eight
Step the switches from 000 to 111.
Connect to the real world
Think of the eight outputs as chip selects for eight memory chips.
How do you build a 3-to-8 decoder selector?
Three switches pick one of eight LEDs through a 74HC138, the way chip selects work in computers. You need 74HC138 3-to-8 decoder, DIP switch 8-position, Resistor 10 kΩ × 3, LED 5 mm red × 8, Resistor 330 Ω × 8, Breadboard 830 Tie Points, Jumper wires male to male (40 pcs, 20 cm), Breadboard power supply module (MB102) and 12 V 2 A DC adapter. It takes 7 steps and about 45 minutes.
- Level
- Beginner
- Time
- About 45 min
- Parts
- 9
Parts list
- Integrated CircuitsBuy
- SwitchesBuy
- PassivesBuyResistor 10 kΩ × 3
- SemiconductorsBuyLED 5 mm red × 8
- PassivesBuyResistor 330 Ω × 8
- PrototypingBuy
- PrototypingBuy
- PowerBuy
- PowerBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| 74HC138 pin 16 (VCC) and pin 8 (GND) | +5 V and GND | Power |
| Pins 4 and 5 (E1, E2, active low) | GND | Enabled |
| Pin 6 (E3, active high) | +5 V | Enabled |
| Switches A, B, C | One side +5 V, other side to pins 1, 2 and 3 with 10 kΩ to GND | Address inputs |
| LED anodes | 330 Ω to +5 V | Current limit |
| LED cathodes | Y0 to Y7 (pins 15, 14, 13, 12, 11, 10, 9, 7) | Active-low outputs |
No code needed
No code. Power: a breadboard power supply module (MB102) from the 12 V adapter, with its jumper set to 5 V. The outputs go low for the selected address, so each LED is wired from +5 V through a resistor into its output pin and lights when that output is pulled low.
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| Address 000 | Only the LED on Y0 lights |
| Address 101 | Only the LED on Y5 lights |
| Address 111 | Only the LED on Y7 lights |
| Disable (E3 to GND) | All LEDs off |
If it does not work
All LEDs on or none
An enable pin is wrong. Check pins 4, 5 and 6.
Two LEDs light
An address pin is floating. Add a pull-down.
LED order looks wrong
Y7 is on pin 7, which is out of sequence. Check the pin list.
Nothing lights
LEDs are backwards or power is off.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the 3-to-8 decoder selector?
74HC138 3-to-8 decoder, DIP switch 8-position, Resistor 10 kΩ × 3, LED 5 mm red × 8, Resistor 330 Ω × 8, Breadboard 830 Tie Points, Jumper wires male to male (40 pcs, 20 cm), Breadboard power supply module (MB102) and 12 V 2 A DC adapter.
How long does the 3-to-8 decoder selector take to build?
About 45 minutes for a beginner maker, in 7 steps.
How do I know the 3-to-8 decoder selector works?
Address 000: Only the LED on Y0 lights. Address 101: Only the LED on Y5 lights. Address 111: Only the LED on Y7 lights.
All LEDs on or none: what should I check?
An enable pin is wrong. Check pins 4, 5 and 6.
Two LEDs light: what should I check?
An address pin is floating. Add a pull-down.
LED order looks wrong: what should I check?
Y7 is on pin 7, which is out of sequence. Check the pin list.
Nothing lights: what should I check?
LEDs are backwards or power is off.
