Order ready bell for a kitchen
Build it step by step
0 of 7 donePair the remote
Learn the buttons.
Read the outputs
Print which is high.
Show the number
On the display.
Add the chime
Three beeps.
Add the clear rule
Second press clears.
Test the range
Through walls.
Fit it at the counter
Receiver aerial clear.
How do you build an order ready bell for a kitchen?
A button in the kitchen rings a wireless bell and shows the order number at the counter. You need Arduino Nano, 433 MHz 4-channel remote and receiver, TM1637 4-digit display and Active buzzer 5 V. It takes 7 steps and about 90 minutes.
- Level
- Beginner
- Time
- About 90 min
- Parts
- 4
Parts list
- Development BoardsBuyArduino Nano × 1
- WirelessBuy
- DisplaysBuy
- Motors & ActuatorsBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| Receiver outputs D0, D1, D2, D3 | Nano D2, D3, D4, D7 | One output for each remote button |
| Receiver VCC and GND | Nano 5V and GND | Power |
| TM1637 CLK and DIO | Nano D5 and D6 | Display |
| TM1637 VCC and GND | Nano 5V and GND | Power |
| Buzzer plus and minus | Nano D8 and GND | Bell |
Code
The four-button remote and its receiver module are a ready-made radio link: pressing a button makes one output on the receiver go high, so the Nano simply watches four input pins. Each button stands for an order or table number from one to four; pressing it makes the counter display show the number and ring three times, and pressing it again clears it. The module learns the remote's code, so other remotes nearby do not trigger it, but 433 MHz remotes are not secure, so this is a convenience, not a safety system. Test the range through the walls and the kitchen equipment, because metal shelves block the signal; moving the receiver aerial or adding a wire about 17 cm long usually helps. Some receivers hold an output while the button is down (momentary) and some latch it (toggle), so check which yours does and adjust the clear rule. Keep the chime short in a busy kitchen. Arduino IDE, board "Arduino Nano" (try the Old Bootloader option if the upload fails).
Runs on a virtual Arduino Nano in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).
// Order ready bell: each remote button is an order or table number (1 to 4). Press it in the kitchen and the counter rings and shows the number.
// Press the same button again to clear it. Library: TM1637Display. Board: Arduino Nano.
#include <TM1637Display.h>
TM1637Display display(5, 6);
const byte INPUTS[4] = {2, 3, 4, 7}; // receiver outputs D0 to D3
const byte BUZZER = 8;
int shown = 0; // 0 means nothing is called
bool last[4] = {false, false, false, false};
void ring(int times) { for (int i = 0; i < times; i++) { tone(BUZZER, 1600, 150); delay(300); } }
void setup() {
for (byte i = 0; i < 4; i++) pinMode(INPUTS[i], INPUT);
pinMode(BUZZER, OUTPUT);
display.setBrightness(5);
display.clear();
}
void loop() {
for (int i = 0; i < 4; i++) {
bool now = digitalRead(INPUTS[i]);
if (now && !last[i]) { // a new press
int n = i + 1;
if (shown == n) { shown = 0; display.clear(); } // second press clears
else { shown = n; display.showNumberDec(n, false); ring(3); }
}
last[i] = now;
}
delay(20);
}Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| Press 1 | Display shows 1, bell rings |
| Press 1 again | Display clears |
| Press 3 | Display shows 3 |
| Far corner | Still works through a wall |
If it does not work
No response
Check the receiver is paired with the remote.
Rings twice
The receiver is latching; adjust the clear rule.
Short range
Add an aerial wire and move the receiver away from metal.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the order ready bell for a kitchen?
Arduino Nano, 433 MHz 4-channel remote and receiver, TM1637 4-digit display and Active buzzer 5 V.
How long does the order ready bell for a kitchen take to build?
About 90 minutes for a beginner maker, in 7 steps.
How do I know the order ready bell for a kitchen works?
Press 1: Display shows 1, bell rings. Press 1 again: Display clears. Press 3: Display shows 3.
No response: what should I check?
Check the receiver is paired with the remote.
Rings twice: what should I check?
The receiver is latching; adjust the clear rule.
Short range: what should I check?
Add an aerial wire and move the receiver away from metal.
