Projects / Capacitor types and markings tour

Capacitor types and markings tour

Beginner30 minGuided buildReviewed

Build it step by step

0 of 7 done
  1. Sort them

    Group ceramic, film, electrolytic and tantalum capacitors.

  2. Read the codes

    Decode 104, 103 and the plain 22 before measuring.

  3. Find the polarity marks

    Identify the stripe on the electrolytic and the plus mark on the tantalum.

  4. LCR

    Measure each one

    Insert into the tester and note the value.

  5. Compare

    Compare the reading with the printed value and the tolerance.

  6. Note the ratings

    Write down the voltage rating of each.

  7. Think about uses

    Match each to a use: decoupling, timing, power filtering, mains-rated film.

In short

How do you build a capacitor types and markings tour?

Read the codes on ceramic, film and electrolytic capacitors and measure them with a meter. You need Ceramic Capacitor 100 nF, Ceramic capacitor 10 nF, Ceramic capacitor 22 pF, Electrolytic Capacitor 100 µF, Tantalum capacitor 10 µF 16 V, Polyester film capacitor 100 nF (630 V) and LCR / component tester (ESR, transistor). It takes 7 steps and about 30 minutes.

Level
Beginner
Time
About 30 min
Parts
7
See the electronics first. This build uses capacitor charging. Try a capacitor charging in the circuit builder and watch the voltages and currents before you wire it.

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Capacitor leg 1Tester socket pin 1Measurement
Capacitor leg 2Tester socket pin 2Measurement
Electrolytic and tantalum plus leadThe tester's marked plus sidePolarity matters
TesterIts own batterySelf-contained, no other power

No code needed

No code. A three-digit code like 104 means 10 followed by four zeros in picofarads, which is 100 000 pF, 100 nF or 0.1 µF; 103 is 10 nF and a plain 22 is 22 pF. A letter after the code gives the tolerance and the voltage is often printed too. Electrolytic and tantalum capacitors are polarised: a stripe marks the negative lead on an electrolytic, while on a tantalum the marked side is the plus lead. Put them in the wrong way round or over their voltage rating and they can fail loudly. Always discharge a large capacitor with a resistor before measuring. The tester measures with its own small voltage and needs no other power. The 630 V film capacitor is rated for high voltage but you will use it only at low voltage here.

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
104 ceramicAbout 100 nF
103 ceramicAbout 10 nF
ElectrolyticNear 100 µF, often a little high
Tester ESR on the electrolyticA small number of ohms

If it does not work

Tester shows nothing

Check the battery in the tester and discharge the capacitor first.

Value far from printed

Check the code reading and the pin contacts.

Polarity unclear

Check the datasheet; do not guess before applying power.

Electrolytic reads low

It may be old or dried out.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the capacitor types and markings tour?

Ceramic Capacitor 100 nF, Ceramic capacitor 10 nF, Ceramic capacitor 22 pF, Electrolytic Capacitor 100 µF, Tantalum capacitor 10 µF 16 V, Polyester film capacitor 100 nF (630 V) and LCR / component tester (ESR, transistor).

How long does the capacitor types and markings tour take to build?

About 30 minutes for a beginner maker, in 7 steps.

How do I know the capacitor types and markings tour works?

104 ceramic: About 100 nF. 103 ceramic: About 10 nF. Electrolytic: Near 100 µF, often a little high.

Tester shows nothing: what should I check?

Check the battery in the tester and discharge the capacitor first.

Value far from printed: what should I check?

Check the code reading and the pin contacts.

Polarity unclear: what should I check?

Check the datasheet; do not guess before applying power.

Electrolytic reads low: what should I check?

It may be old or dried out.