Projects / Capacitance meter

Capacitance meter

Beginner1 hGuided buildReviewed

Build it step by step

0 of 6 done
  1. UNO

    Wire the display

    SDA to A4, SCL to A5, VCC to 5V, GND to GND.

  2. UNO

    Build the test point

    Put two spare rows on the breadboard for the capacitor. From D11 add the 10 kΩ resistor to the + row, and from D12 the 220 Ω resistor to the same row.

  3. UNO

    Sense the voltage

    Run a wire from the + row to A0 and one from the − row to GND.

  4. UNOHelloPCF8574

    Upload

    Install the LCD library and upload.

  5. UNO

    Measure a known part

    Fit a 100 µF capacitor, + leg on the + row. The display should show close to 100 µF.

  6. UNO

    Use it

    Test unknown capacitors. Always discharge big ones and keep the polarity right.

In short

How do you build a capacitance meter?

Charge a capacitor through a 10 kΩ resistor, time how long it takes to reach 63 % of the supply, and show the capacitance on an LCD. You need Arduino Uno R3, Resistor 10 kΩ, Resistor 220 Ω, 16x2 LCD with I2C backpack (PCF8574), Breadboard 830 Tie Points, Jumper wires male to male (40 pcs, 20 cm) and Electrolytic Capacitor 100 µF. It takes 6 steps and about 60 minutes.

Level
Beginner
Time
About 60 min
Parts
7

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
Uno D1110 kΩ resistor to the capacitor's + legCharge path
Uno D12220 Ω resistor to the capacitor's + legDischarge path
Capacitor + legUno A0Voltage sensing
Capacitor − legUno GNDReturn
LCD SDA / SCLUno A4 / A5I2C display
LCD VCC / GNDUno 5V / GNDDisplay power

Code

Arduino IDE, board "Arduino Uno" (processor ATmega328P, or ATmega328P (Old Bootloader) for clones). Install "LiquidCrystal I2C" by Frank de Brabander. Practical range is about 1 µF to 2000 µF; below that, analogRead() is too slow.

Runs on a virtual Arduino Uno in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

#include <Wire.h>
#include <LiquidCrystal_I2C.h>

LiquidCrystal_I2C lcd(0x27, 16, 2);      // try 0x3F if the screen stays blank
const byte CHARGE = 11, DISCHARGE = 12, SENSE = A0;
const float R_CHARGE = 10000.0;           // ohms; measure your resistor for better accuracy

void setup() {
  pinMode(CHARGE, OUTPUT); digitalWrite(CHARGE, LOW);
  pinMode(DISCHARGE, INPUT);
  lcd.init(); lcd.backlight();
  lcd.print("Capacitance");
}

void loop() {
  // 1. Discharge fully
  pinMode(DISCHARGE, OUTPUT); digitalWrite(DISCHARGE, LOW);
  while (analogRead(SENSE) > 0) {}
  pinMode(DISCHARGE, INPUT);

  // 2. Charge through 10 kohm and time to 63.2 % of 5 V (about 647 of 1023)
  unsigned long t0 = micros();
  digitalWrite(CHARGE, HIGH);
  while (analogRead(SENSE) < 647) { if (micros() - t0 > 20000000UL) break; }
  float seconds = (micros() - t0) / 1000000.0;
  digitalWrite(CHARGE, LOW);

  float uF = seconds / R_CHARGE * 1000000.0;   // C = t / R, shown in microfarads
  lcd.setCursor(0, 1);
  lcd.print("                ");
  lcd.setCursor(0, 1);
  if (uF >= 1) { lcd.print(uF, 1); lcd.print(" uF"); }
  else { lcd.print(uF * 1000.0, 0); lcd.print(" nF"); }
  delay(1000);
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
100 µF electrolytic (about ±20 %)Reads between 80 and 120 µF
1000 µF electrolyticReads in the range 800 to 1200 µF, taking about 10 seconds
No capacitor fittedThe reading is near 0 or very small
Reverse an electrolytic by mistakeDo not do this: it can heat and burst

If it does not work

The LCD is blank

Turn the contrast trimmer on the backpack, and try address 0x3F.

Readings are always about 5 to 10 % off

Measure the 10 kΩ resistor with a multimeter and put the real value in R_CHARGE.

Small capacitors read nonsense

Under 1 µF the charge time is only microseconds. This build is for larger values.

It never finishes

The capacitor may be leaky or a very large value. The sketch gives up after 20 seconds.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the capacitance meter?

Arduino Uno R3, Resistor 10 kΩ, Resistor 220 Ω, 16x2 LCD with I2C backpack (PCF8574), Breadboard 830 Tie Points, Jumper wires male to male (40 pcs, 20 cm) and Electrolytic Capacitor 100 µF. Electrolytic Capacitor 100 µF: Use one to test, with the polarity right.

How long does the capacitance meter take to build?

About 60 minutes for a beginner maker, in 6 steps.

How do I know the capacitance meter works?

100 µF electrolytic (about ±20 %): Reads between 80 and 120 µF. 1000 µF electrolytic: Reads in the range 800 to 1200 µF, taking about 10 seconds. No capacitor fitted: The reading is near 0 or very small.

The LCD is blank: what should I check?

Turn the contrast trimmer on the backpack, and try address 0x3F.

Readings are always about 5 to 10 % off: what should I check?

Measure the 10 kΩ resistor with a multimeter and put the real value in R_CHARGE.

Small capacitors read nonsense: what should I check?

Under 1 µF the charge time is only microseconds. This build is for larger values.

It never finishes: what should I check?

The capacitor may be leaky or a very large value. The sketch gives up after 20 seconds.