Build it step by step
0 of 6 doneBuild the first stage
Wire one BC547 with its base resistor and LED and test it with a 1.5 V cell on the base resistor.
Add the other stages
Add the diode strings so each stage needs more voltage.
Build the peak detector
Add the rectifier diode, the 10 µF capacitor and the 100 kΩ bleed resistor.
Connect audio
Connect a signal with the level control turned down, then turn it up slowly.
Tune the levels
Adjust the potentiometer so normal music lights two to three LEDs.
Compare
Think about how an LM3914 does the same job with comparators instead of diodes.
How do you build a transistor audio level meter?
A few transistors light more LEDs as the music gets louder, with no ICs. You need BC547 NPN transistor × 4, Signal Diode 1N4148 × 7, Resistor 1 kΩ × 4, Resistor 10 kΩ × 4, Resistor 100 kΩ, Potentiometer 10 kΩ, LED 5 mm red × 4, Electrolytic capacitor 10 µF × 2, Breadboard 830 Tie Points, 9 V battery and 9 V battery snap with DC jack. It takes 6 steps and about 60 minutes.
- Level
- Beginner
- Time
- About 60 min
- Parts
- 11
Parts list
- SemiconductorsBuy
- SemiconductorsBuy
- PassivesBuyResistor 1 kΩ × 4
- PassivesBuyResistor 10 kΩ × 4
- PassivesBuyResistor 100 kΩ × 1
- PassivesBuy
- SemiconductorsBuyLED 5 mm red × 4
- PassivesBuy
- PrototypingBuy
- BatteriesBuy9 V battery × 1
- PowerBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| Audio in (speaker terminal of an amplifier, or loud headphone out) | 10 kΩ potentiometer outer pins, other end to ground | Level control |
| Potentiometer wiper | 10 µF capacitor + | Coupling |
| 10 µF capacitor - | 1N4148 anode | Peak rectifier |
| 1N4148 cathode | Envelope node E | Peak detector |
| Envelope node E | 10 µF capacitor + and 100 kΩ resistor, both to ground | Holds the peak and bleeds away |
| Stage 1: E | 10 kΩ resistor to BC547 base | Lights at about 0.65 V |
| Stage 2: E | One 1N4148 then 10 kΩ to base | About 1.3 V |
| Stage 3: E | Two 1N4148 in series then 10 kΩ to base | About 1.9 V |
| Stage 4: E | Three 1N4148 in series then 10 kΩ to base | About 2.6 V |
| Every BC547 emitter | - rail | Ground |
| Each BC547 collector | LED cathode, LED anode to 1 kΩ then + rail | One LED per stage |
| 9 V battery | + rail and - rail | Supply and common ground with the audio |
No code needed
No code. BC547 flat face towards you with legs down: collector, base, emitter from the left. The audio source and the circuit must share a ground; use a low-volume signal first. Never connect an amplifier's speaker terminal without the 10 kΩ potentiometer in place as a series resistance; keep the wiper at the low end when you power up. Diode drops are about 0.65 V each, so the four stages light at roughly 0.65, 1.3, 1.9 and 2.6 V on the envelope node.
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| No sound | No LEDs |
| Quiet music | One or two LEDs |
| Loud music | All four LEDs flicker with the beat |
| Music stopped | LEDs fall away over about a second |
If it does not work
No LED lights
Check the audio level and the rectifier diode direction.
All LEDs light together
Diode strings are missing. Add the 1N4148 diodes.
LEDs do not fall away
The 100 kΩ bleed resistor is missing.
Hum on the LEDs
The grounds are not shared. Link the audio and battery grounds.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the transistor audio level meter?
BC547 NPN transistor × 4, Signal Diode 1N4148 × 7, Resistor 1 kΩ × 4, Resistor 10 kΩ × 4, Resistor 100 kΩ, Potentiometer 10 kΩ, LED 5 mm red × 4, Electrolytic capacitor 10 µF × 2, Breadboard 830 Tie Points, 9 V battery and 9 V battery snap with DC jack.
How long does the transistor audio level meter take to build?
About 60 minutes for a beginner maker, in 6 steps.
How do I know the transistor audio level meter works?
No sound: No LEDs. Quiet music: One or two LEDs. Loud music: All four LEDs flicker with the beat.
No LED lights: what should I check?
Check the audio level and the rectifier diode direction.
All LEDs light together: what should I check?
Diode strings are missing. Add the 1N4148 diodes.
LEDs do not fall away: what should I check?
The 100 kΩ bleed resistor is missing.
Hum on the LEDs: what should I check?
The grounds are not shared. Link the audio and battery grounds.
