Projects / MKR WiFi 1010 signal strength meter

MKR WiFi 1010 signal strength meter

Beginner2 hGuided buildReviewed

Build it step by step

0 of 7 done
  1. ARDUINO

    Wire the display

    VCC and GND, SDA to pin 11, SCL to pin 12.

  2. ARDUINO19.4 mASSD1306

    Install the libraries

    WiFiNINA, Adafruit SSD1306 and Adafruit GFX.

  3. ARDUINO

    Edit the sketch

    Put your Wi-Fi name and password in the placeholders.

  4. ARDUINO

    Upload it

    The display says Joining Wi-Fi, then shows a dBm number.

  5. ARDUINO

    Walk around with a power bank

    The bar rises near the router.

  6. ARDUINO

    Go behind a wall

    The signal falls.

  7. ARDUINO

    Note the best spots

    And the weak ones.

In short

How do you build an MKR WiFi 1010 signal strength meter?

An Arduino MKR WiFi 1010 measures the Wi-Fi signal strength of your own network and draws it as a bar on an OLED, to find the best spot for a router or a sensor. You need Arduino MKR WiFi 1010, SSD1306 OLED Display and Breadboard 830 Tie Points. It takes 7 steps and about 120 minutes.

Level
Beginner
Time
About 120 min
Parts
3

Parts list

Tick what you already own. It saves to My Garage, so “Build with what I have” knows.

Wiring

FromToWhy
OLED VCCMKR VCC pinPower at 3.3 V
OLED GNDMKR GND pinCommon ground
OLED SDAMKR pin 11 (SDA)I2C data
OLED SCLMKR pin 12 (SCL)I2C clock

Code

Wi-Fi signal strength is reported as RSSI, a negative number of decibels relative to a milliwatt, where closer to zero is stronger. Around minus 40 to minus 50 is excellent, minus 60 is good for streaming, minus 70 is the edge of reliable use and minus 80 is unreliable. The MKR WiFi 1010 has a separate Wi-Fi chip, called the NINA module, and the WiFiNINA library talks to it. Once the board has joined your own network, one call returns the current signal strength. The program draws it as a number and a bar and keeps the best value seen, so you can walk around the house with the board on a power bank and see which spots are good and which are weak. This is useful for placing a router, an extender or a Wi-Fi sensor. The board only joins 2.4 GHz networks. The name and password in the sketch are placeholders; use your own and never share the sketch with the real ones in it.

Runs on a virtual Arduino MKR WiFi 1010 in your browser, with sliders for the sensors. Happy with it? Verify and upload to your real board from the same page (Chrome or Edge on a computer).

#include <SPI.h>
#include <WiFiNINA.h>
#include <Wire.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>

const char WIFI_NAME[] = "YOUR_WIFI_NAME";         // placeholders: use your own network
const char WIFI_PASSWORD[] = "YOUR_WIFI_PASSWORD";

Adafruit_SSD1306 oled(128, 64, &Wire, -1);
long best = -120;

const char* quality(long rssi) {
  if (rssi > -50) return "Excellent";
  if (rssi > -60) return "Good";
  if (rssi > -70) return "Fair";
  if (rssi > -80) return "Weak";
  return "Very weak";
}

void setup() {
  Wire.begin();                                    // pins 11 and 12 on the MKR
  if (!oled.begin(SSD1306_SWITCHCAPVCC, 0x3C)) { while (true) {} }
  oled.clearDisplay();
  oled.setTextColor(SSD1306_WHITE);
  oled.setCursor(0, 0);
  oled.print("Joining Wi-Fi...");
  oled.display();
  while (WiFi.begin(WIFI_NAME, WIFI_PASSWORD) != WL_CONNECTED) {
    delay(3000);
  }
}

void loop() {
  long rssi = WiFi.RSSI();                         // signal strength in dBm, closer to 0 is stronger
  if (rssi > best) best = rssi;
  int bar = constrain(map(rssi, -90, -30, 0, 120), 0, 120);

  oled.clearDisplay();
  oled.setTextSize(1);
  oled.setCursor(0, 0);
  oled.print(WIFI_NAME);
  oled.setTextSize(2);
  oled.setCursor(0, 14);
  oled.print(rssi); oled.print(" dBm");
  oled.drawRect(0, 38, 124, 10, SSD1306_WHITE);
  oled.fillRect(2, 40, bar, 6, SSD1306_WHITE);
  oled.setTextSize(1);
  oled.setCursor(0, 54);
  oled.print(quality(rssi)); oled.print("  best "); oled.print(best);
  oled.display();
  delay(500);
}

Test checklist

What you should see at each check. If a reading is far off, stop and use the troubleshooting list.

CheckExpected
Next to the routerStrong, better than minus 50
In the next roomFair or good
Behind a thick wallWeaker by 10 or 20 dBm
Far end of the houseWeak
Best valueKeeps the highest seen

If it does not work

Stays on Joining Wi-Fi

Check the name and password, and that the network is 2.4 GHz.

Display blank

Check the I2C wires on pins 11 and 12 and the address 0x3C.

Does not compile

Install the WiFiNINA library and the SAMD board package.

Number jumps around

This is normal, watch the trend, not each value.

Firmware warning

Update the Wi-Fi firmware with the Arduino IDE's updater tool if asked.

Still stuck? Find the fault step by step with your multimeter →

Ask Lark AI

Common questions

What parts do I need for the MKR WiFi 1010 signal strength meter?

Arduino MKR WiFi 1010, SSD1306 OLED Display and Breadboard 830 Tie Points.

How long does the MKR WiFi 1010 signal strength meter take to build?

About 120 minutes for a beginner maker, in 7 steps.

How do I know the MKR WiFi 1010 signal strength meter works?

Next to the router: Strong, better than minus 50. In the next room: Fair or good. Behind a thick wall: Weaker by 10 or 20 dBm.

Stays on Joining Wi-Fi: what should I check?

Check the name and password, and that the network is 2.4 GHz.

Display blank: what should I check?

Check the I2C wires on pins 11 and 12 and the address 0x3C.

Does not compile: what should I check?

Install the WiFiNINA library and the SAMD board package.

Number jumps around: what should I check?

This is normal, watch the trend, not each value.