Build it step by step
0 of 5 donePlace the 555
Across the centre gap, notch on the left. Pin 1 is bottom left, pins count anticlockwise.
Power and reset
Pin 8 and pin 4 to plus, pin 1 to minus.
Timing parts
R1 from plus to pin 7, R2 from pin 7 to pin 6. Link pin 6 to pin 2. 100 µF from pin 2 to minus.
Pin 5 and output
10 nF from pin 5 to minus. 470 Ω and the LED from pin 3 to minus.
Time it
Connect the battery and count flashes for 30 s. Then swap 100 µF for 10 µF and watch it speed up ten times.
How do you build a 555 timer LED flasher?
A NE555 in astable mode blinks an LED about once a second, and changing one capacitor changes the speed. You need NE555 Timer IC, Resistor 1 kΩ, Resistor 10 kΩ, Electrolytic Capacitor 100 µF, Ceramic capacitor 10 nF, LED 5 mm red, Resistor 470 Ω, 9 V battery, 9 V battery snap with DC jack, Breadboard 400 points (half size) and Jumper wires male to male (40 pcs, 20 cm). It takes 5 steps and about 35 minutes.
- Level
- Beginner
- Time
- About 35 min
- Parts
- 11
Parts list
- Integrated CircuitsBuyNE555 Timer IC × 1
- PassivesBuyResistor 1 kΩ × 1
- PassivesBuyResistor 10 kΩ × 1
- PassivesBuy
- PassivesBuy
- SemiconductorsBuyLED 5 mm red × 1
- PassivesBuyResistor 470 Ω × 1
- BatteriesBuy9 V battery × 1
- PowerBuy
- PrototypingBuy
- PrototypingBuy
Tick what you already own. It saves to My Garage, so “Build with what I have” knows.
Wiring
| From | To | Why |
|---|---|---|
| 555 pin 8 and pin 4 | 9 V + | Power and reset held high |
| 555 pin 1 | 9 V − | Ground |
| 9 V + | 1 kΩ (R1) to pin 7 | Charge path |
| Pin 7 | 10 kΩ (R2) to pins 6 and 2 (joined) | Charge and discharge path |
| Pins 6 and 2 | 100 µF to ground, minus to ground | Timing capacitor |
| Pin 5 | 10 nF to ground | Keeps the threshold steady |
| Pin 3 | 470 Ω, LED anode, LED cathode to ground | Output |
No code needed
No code. Frequency f = 1.44 / ((R1 + 2·R2)·C) = 1.44 / (21 kΩ × 100 µF) ≈ 0.69 Hz. On time ≈ 0.693 × (R1 + R2) × C ≈ 0.76 s, off time ≈ 0.693 × R2 × C ≈ 0.69 s.
Test checklist
What you should see at each check. If a reading is far off, stop and use the troubleshooting list.
| Check | Expected |
|---|---|
| Flashes in 30 s with 100 µF | About 20 (0.69 Hz) |
| On time vs off time | On slightly longer than off (0.76 s vs 0.69 s) |
| With 10 µF instead | About 7 flashes per second |
| Pin 3 voltage when on | About 7.5 to 8 V on a 9 V supply |
If it does not work
LED stays on or off
Pin 4 not tied to plus, or pins 2 and 6 not joined.
Much slower than expected
Electrolytic capacitors are often +20 % or more. Measure with a capacitance meter.
Gets warm
The 555 or LED is backwards. Check the notch and the LED's long leg.
Still stuck? Find the fault step by step with your multimeter →
Common questions
What parts do I need for the 555 timer LED flasher?
NE555 Timer IC, Resistor 1 kΩ, Resistor 10 kΩ, Electrolytic Capacitor 100 µF, Ceramic capacitor 10 nF, LED 5 mm red, Resistor 470 Ω, 9 V battery, 9 V battery snap with DC jack, Breadboard 400 points (half size) and Jumper wires male to male (40 pcs, 20 cm).
How long does the 555 timer LED flasher take to build?
About 35 minutes for a beginner maker, in 5 steps.
How do I know the 555 timer LED flasher works?
Flashes in 30 s with 100 µF: About 20 (0.69 Hz). On time vs off time: On slightly longer than off (0.76 s vs 0.69 s). With 10 µF instead: About 7 flashes per second.
LED stays on or off: what should I check?
Pin 4 not tied to plus, or pins 2 and 6 not joined.
Much slower than expected: what should I check?
Electrolytic capacitors are often +20 % or more. Measure with a capacitance meter.
Gets warm: what should I check?
The 555 or LED is backwards. Check the notch and the LED's long leg.
