Lab / JNTUH / Electronic devices / Experiment 3

Half-wave and full-wave rectifiers with and without filter

Electronic devicesVirtual readings4 viva questionsRecord book ready
Aim

To build half-wave, full-wave and bridge rectifiers, and measure Vdc, Vrms and the ripple factor with and without a capacitor filter.

Apparatus
  • Step-down transformer 230 V / 9-0-9 V
  • Diodes 1N4007 × 4
  • Capacitors 100 µF and 470 µF
  • Load resistor 1 kΩ
  • CRO and multimeter

Theory

A half-wave rectifier passes one half of each cycle: Vdc = Vm/π, ripple factor 1.21. A full-wave (centre-tap or bridge) passes both halves: Vdc = 2Vm/π, ripple factor 0.482. A capacitor across the load charges to the peak and discharges slowly, so the ripple drops to about Vr(p-p) = Idc / (f·C), where f is 50 Hz for half-wave and 100 Hz for full-wave. Vm here is the peak after the diode drops.

Read the lesson: Diodes protection ›
Circuit connections
  • Half-wave: secondary → diode → load → secondary
  • Bridge: four diodes in a bridge, load across the output; capacitor across the load for the filter

Procedure

Pre-lab check

4 questions · 75% to be ready
1What is ripple factor?
2Why is the bridge rectifier preferred?
3What is PIV?
4How does an inductor filter work?

Try the readings before the lab

Calculated, not measured. In the lab, write down your own readings.
QuantityValue
Peak output Vm (V)11.33
Vdc (V)11.21
Ripple Vr p-p (V)0.24
Ripple factor0.0061
Ripple frequency100 Hz
PIV per diode (V)12.73

Precautions

  • The transformer primary is at mains voltage: only the teacher connects it, and the bench stays dry.
  • Connect electrolytic capacitors the right way round and rated above the peak voltage.
  • Never connect the CRO ground to both ends of the bridge output and the transformer at once.

My readings

Type what you measured. It goes into your record book, and to My Garage when you are signed in.

S. No.QuantityValue
1
2
3
4
5
6

Check my readings

Put the value you set in the first column, then compare. Real parts have tolerance.

Open my record book
Result

Ripple factor without filter: half-wave ___, full-wave ___. With ___ µF it falls to ___. The bridge rectifier gives the highest Vdc for the same transformer.

Everything above is free. The print-ready write-up comes with Maker.

Printed pages leave the observation table empty for your own readings.

Viva questions

Say your answer out loud first, then check. The first 2 answers are free; Maker opens all 4.

1. What is ripple factor?
2. Why is the bridge rectifier preferred?
3. What is PIV?
4. How does an inductor filter work?

Quick answers for your record and viva

What is the aim of the half-wave and full-wave rectifiers with and without filter experiment?

To build half-wave, full-wave and bridge rectifiers, and measure Vdc, Vrms and the ripple factor with and without a capacitor filter.

What apparatus is needed for half-wave and full-wave rectifiers with and without filter?

Step-down transformer 230 V / 9-0-9 V, Diodes 1N4007 × 4, Capacitors 100 µF and 470 µF, Load resistor 1 kΩ, CRO and multimeter.

What is the theory behind half-wave and full-wave rectifiers with and without filter?

A half-wave rectifier passes one half of each cycle: Vdc = Vm/π, ripple factor 1.21. A full-wave (centre-tap or bridge) passes both halves: Vdc = 2Vm/π, ripple factor 0.482. A capacitor across the load charges to the peak and discharges slowly, so the ripple drops to about Vr(p-p) = Idc / (f·C), where f is 50 Hz for half-wave and 100 Hz for full-wave. Vm here is the peak after the diode drops.

What result should I get in half-wave and full-wave rectifiers with and without filter?

Ripple factor without filter: half-wave ___, full-wave ___. With ___ µF it falls to ___. The bridge rectifier gives the highest Vdc for the same transformer.

What precautions should I take in half-wave and full-wave rectifiers with and without filter?

The transformer primary is at mains voltage: only the teacher connects it, and the bench stays dry. Connect electrolytic capacitors the right way round and rated above the peak voltage. Never connect the CRO ground to both ends of the bridge output and the transformer at once.

Half-wave and full-wave rectifiers with and without filter