Lab / SPPU / Analog and linear ICs / Experiment 2

Op-amp adder (summing) and subtractor (difference) amplifiers

Analog and linear ICsVirtual readings4 viva questionsRecord book ready
Aim

To build an inverting summing amplifier and a difference amplifier and verify their outputs.

Apparatus
  • IC 741
  • Resistors 10 kΩ × 6
  • Dual supply ±12 V
  • Two DC sources (or dividers from the supply)
  • Multimeter
ABY

Theory

Summing amplifier with equal resistors: Vo = −(V1 + V2 + …). With unequal input resistors it gives a weighted sum: Vo = −Rf (V1/R1 + V2/R2). Difference amplifier with all four resistors equal: Vo = V2 − V1, where V2 goes to the non-inverting side.

Read the lesson: Adc measurement ›
Circuit connections
  • Adder: V1 → 10 kΩ and V2 → 10 kΩ, both to pin 2; Rf 10 kΩ from pin 2 to pin 6; pin 3 to ground
  • Subtractor: V1 → 10 kΩ → pin 2; Rf 10 kΩ pin 2 to 6; V2 → 10 kΩ → pin 3; 10 kΩ from pin 3 to ground

Procedure

Pre-lab check

4 questions · 75% to be ready
1Why is the inverting adder preferred to a non-inverting one?
2What is CMRR?
3How do you make an averaging amplifier?
4Where is a difference amplifier used?

Try the readings before the lab

Calculated, not measured. In the lab, write down your own readings.
V1 (V)V2 (V)Vo theory (V)
11-2
12-3
20.5-2.5
32-5
-12-1
0.5-1.51

Precautions

  • Use resistors of the same tolerance (1% if available) for the subtractor.
  • Keep outputs within the supply swing.

My readings

Type what you measured. It goes into your record book, and to My Garage when you are signed in.

S. No.V1 (V)V2 (V)Vo theory (V)
1
2
3
4
5
6

Check my readings

Put the value you set in the first column, then compare. Real parts have tolerance.

Open my record book
Result

The adder gives Vo = −(V1 + V2) and the subtractor Vo = V2 − V1, within ___ % of theory.

Everything above is free. The print-ready write-up comes with Maker.

Printed pages leave the observation table empty for your own readings.

Viva questions

Say your answer out loud first, then check. The first 2 answers are free; Maker opens all 4.

1. Why is the inverting adder preferred to a non-inverting one?
2. What is CMRR?
3. How do you make an averaging amplifier?
4. Where is a difference amplifier used?

Quick answers for your record and viva

What is the aim of the op-amp adder (summing) and subtractor (difference) amplifiers experiment?

To build an inverting summing amplifier and a difference amplifier and verify their outputs.

What apparatus is needed for op-amp adder (summing) and subtractor (difference) amplifiers?

IC 741, Resistors 10 kΩ × 6, Dual supply ±12 V, Two DC sources (or dividers from the supply), Multimeter.

What is the theory behind op-amp adder (summing) and subtractor (difference) amplifiers?

Summing amplifier with equal resistors: Vo = −(V1 + V2 + …). With unequal input resistors it gives a weighted sum: Vo = −Rf (V1/R1 + V2/R2). Difference amplifier with all four resistors equal: Vo = V2 − V1, where V2 goes to the non-inverting side.

What result should I get in op-amp adder (summing) and subtractor (difference) amplifiers?

The adder gives Vo = −(V1 + V2) and the subtractor Vo = V2 − V1, within ___ % of theory.

What precautions should I take in op-amp adder (summing) and subtractor (difference) amplifiers?

Use resistors of the same tolerance (1% if available) for the subtractor. Keep outputs within the supply swing.

Op-amp adder (summing) and subtractor (difference) amplifiers