Diode clippers and clampers
To build positive and negative clippers and a positive clamper, and observe their output waveforms.
- Function generator
- Diodes 1N4148
- Resistor 10 kΩ
- Capacitor 1 µF
- DC supply for the reference
- CRO
Theory
A clipper removes the part of a signal above (or below) a level. In a shunt positive clipper with reference Vref, the output cannot rise above Vref + 0.7 V because the diode conducts. A clamper shifts the whole waveform up or down without changing its shape: a capacitor charges to the peak through the diode, so a positive clamper output swings from about −0.7 V to 2Vm − 0.7 V.
Read the lesson: Diodes protection ›- Clipper: input → 10 kΩ → output; diode (anode at output) in series with Vref from output to ground
- Clamper: input → capacitor → output; diode from output to ground (anode to ground for positive clamping); 100 kΩ load
Procedure
Pre-lab check
4 questions · 75% to be readyTry the readings before the lab
| Phase (°) | Vin (V) | Clipper out (V) | Clamper out (V) |
|---|---|---|---|
| 0 | 0 | 0 | 4.3 |
| 30 | 2.5 | 2.5 | 6.8 |
| 60 | 4.33 | 2.7 | 8.63 |
| 90 | 5 | 2.7 | 9.3 |
| 120 | 4.33 | 2.7 | 8.63 |
| 150 | 2.5 | 2.5 | 6.8 |
| 180 | 0 | 0 | 4.3 |
| 210 | -2.5 | -2.5 | 1.8 |
| 240 | -4.33 | -4.33 | -0.03 |
| 270 | -5 | -5 | -0.7 |
| 300 | -4.33 | -4.33 | -0.03 |
| 330 | -2.5 | -2.5 | 1.8 |
| 360 | 0 | 0 | 4.3 |
Precautions
- Use DC coupling on the CRO to see the clamper's shift.
- Choose RC much longer than the signal period for the clamper.
My readings
Type what you measured. It goes into your record book, and to My Garage when you are signed in.
| S. No. | Phase (°) | Vin (V) | Clipper out (V) | Clamper out (V) |
|---|---|---|---|---|
| 1 | ||||
| 2 | ||||
| 3 | ||||
| 4 | ||||
| 5 | ||||
| 6 |
Check my readings
Put the value you set in the first column, then compare. Real parts have tolerance.
The clipper limits the output at ___ V (Vref + 0.7 V). The clamper shifts the waveform up by ___ V while keeping its shape.
Everything above is free. The print-ready write-up comes with Maker.
Printed pages leave the observation table empty for your own readings.
Viva questions
Say your answer out loud first, then check. The first 2 answers are free; Maker opens all 4.
Quick answers for your record and viva
What is the aim of the diode clippers and clampers experiment?
To build positive and negative clippers and a positive clamper, and observe their output waveforms.
What apparatus is needed for diode clippers and clampers?
Function generator, Diodes 1N4148, Resistor 10 kΩ, Capacitor 1 µF, DC supply for the reference, CRO.
What is the theory behind diode clippers and clampers?
A clipper removes the part of a signal above (or below) a level. In a shunt positive clipper with reference Vref, the output cannot rise above Vref + 0.7 V because the diode conducts. A clamper shifts the whole waveform up or down without changing its shape: a capacitor charges to the peak through the diode, so a positive clamper output swings from about −0.7 V to 2Vm − 0.7 V.
What result should I get in diode clippers and clampers?
The clipper limits the output at ___ V (Vref + 0.7 V). The clamper shifts the waveform up by ___ V while keeping its shape.
What precautions should I take in diode clippers and clampers?
Use DC coupling on the CRO to see the clamper's shift. Choose RC much longer than the signal period for the clamper.
